From: Manny Gonzalez (gonzalu@xxxxxxx)
Date: Sun Mar 03 2002 - 18:45:01 GMT-3
MULTIRING [ALL] [IP,IPX,etc] is for Source Route Bridging on Token Ring
(SRB) not SRT or TRANSPARENT BRIDGING on ETH.
Example, if you have a bridge that is in Source Route Bridging mode, you
better have that router listen and adapt to RIF's. This is what the
command multiring does. I usually just do multiring all and be done with
it. But be aware of the options in case you are asked to only SRB a
specific protocol.
Anand Ghody wrote:
>
> How? its not an option.
>
> below is r3
>
> lone_rhino(config)#int e0
> lone_rhino(config-if)#m?
> mac-address max-reserved-bandwidth media-type mtu multilink-group
>
> Raj wrote:
>
> >Try to Pu the Multiring IP on the R3 routers ethrnet and see. It shousl
> >work.
> >
> >Raj.
> >----- Original Message -----
> >From: "Anand Ghody" <vze2hq65@verizon.net>
> >To: "alain faure" <alainfaure@yahoo.fr>
> >Cc: <ccielab@groupstudy.com>
> >Sent: Sunday, March 03, 2002 12:13 PM
> >Subject: Re: translational bridging driving be nuts!!!
> >
> >
> >>Tried that already, does not work (multiring ipon all token ring
> >>interfaces and only on r4's token ring interface). The fun thing is
> >>that I setup the cat 3900 with an ip address, 172.16.3.5/24 ( on the
> >>same subnet). I can see its arp request for 172.16.3.1 (r1) on the
> >>ethernet interface of (r3) 172.16.3.2 when I run debug arp. I just
> >>can't ping from 172.16.3.2 to 172.16.3.1.
> >>
> >>and in response to the first post I think you meant multiring ip in the
> >>token ring interface of r4. and as answered above that does not do the
> >>trick
> >>
> >>alain faure wrote:
> >>
> >>>Hi,
> >>>
> >>>Is it necessary to put a multiring all on the token ring interface for
> >>>
> >this
> >
> >>>case ?
> >>>
> >>>Best regards
> >>>
> >>>--- Anand Ghody <vze2hq65@verizon.net> a icrit : > Alright, I have no
> >>>
> >idea why
> >
> >>>this is not working and need help. I
> >>>
> >>>>checked previous posts and made some adjustments but it still does not
> >>>>work Need help!!!
> >>>>
> >>>>heres the setup
> >>>>
> >>>>r3 (e0, 172.16.3.2) -> catalyst 5505 port 2/2 -> catalyst 5505 port
> >>>>
> >2/1 ->
> >
> >>>>r4 (e0) -> r4 (to0) -> cat 3900 port 1 ->cat 3900 port 6 -> r1 (to0,
> >>>>172.16.3.1)
> >>>>
> >>>>
> >>>>I have disable ip routing on r4 and also setup bridge 1 bitswap-layer3
> >>>>address
> >>>>
> >>>>the ports on the cataylst 5500 are on the same vlan
> >>>>the port on the cataylst 3900 are also in the same vlan and setup for
> >>>>
> >srt
> >
> >>>>If I but an ip address on r4 token ring I can ping it from r1
> >>>>
> >>>>I'll past the configs to make it easier
> >>>>
> >>>>
> >>>>r3 config
> >>>>!
> >>>>interface Ethernet0
> >>>>ip address 172.16.3.2 255.255.255.0
> >>>>
> >>>>|
> >>>>connnects to catalyst 5500
> >>>>|
> >>>>
> >>>>r4 config
> >>>>no ip routing
> >>>>no ip finger
> >>>>!
> >>>>!
> >>>>source-bridge ring-group 100
> >>>>source-bridge transparent 100 3 2 1
> >>>>!
> >>>>!
> >>>>interface Ethernet0
> >>>>no ip address
> >>>>no ip route-cache
> >>>>bridge-group 1
> >>>>!
> >>>>interface Serial0
> >>>>no ip address
> >>>>no ip route-cache
> >>>>shutdown
> >>>>!
> >>>>interface Serial1
> >>>>no ip address
> >>>>no ip route-cache
> >>>>shutdown
> >>>>!
> >>>>interface TokenRing0
> >>>>no ip address
> >>>>no ip route-cache
> >>>>ring-speed 16
> >>>>source-bridge 1 2 100
> >>>>!
> >>>>ip classless
> >>>>no ip http server
> >>>>!
> >>>>bridge 1 protocol ieee
> >>>>bridge 1 bitswap-layer3-addresses
> >>>>!
> >>>>
> >>>>|
> >>>>connects to catalyst 3900
> >>>>|
> >>>>
> >>>>r1 config
> >>>>!
> >>>>interface TokenRing0
> >>>>ip address 172.16.3.1 255.255.255.0
> >>>>ring-speed 16
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>.
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:51 GMT-3