From: kym blair (kymblair@xxxxxxxxxxx)
Date: Tue Feb 05 2002 - 11:25:43 GMT-3
This works great for me on two routers back-to-back:
Router6:
interface ATM0
no ip address
no atm ilmi-keepalive
!
interface ATM0.1 multipoint
ip address 150.50.9.1 255.255.255.252
pvc 6/102
protocol ip 150.50.9.1 broadcast
protocol ip 150.50.9.2 broadcast
encapsulation aal5snap
Router9:
interface ATM0
no ip address
atm clock INTERNAL
no atm ilmi-keepalive
!
interface ATM0.1 multipoint
ip address 150.50.9.2 255.255.255.252
pvc 6/102
protocol ip 150.50.9.1 broadcast
protocol ip 150.50.9.2 broadcast
encapsulation aal5snap
You can add rate-limit and change encap, pvc, etc. Can change to
point-to-point subinterface, or just physical interface if you want. Need a
switch to do svc.
HTH,
Kym
>From: Erhan Kurt <iekurt@yahoo.com>
>Reply-To: Erhan Kurt <iekurt@yahoo.com>
>To: JOSE ANGEL MARTINEZ DE LA VARA <jamartinez@landata.payma.es>,
>ccielab@groupstudy.com
>Subject: RE: ATM with back to back routers
>Date: Mon, 4 Feb 2002 06:36:56 -0800 (PST)
>
>Use ATM-DXI:
>
>http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_c/
wcdatm.htm#xtocid98
>
>
>Erhan
>
>
>--- JOSE ANGEL MARTINEZ DE LA VARA
><jamartinez@landata.payma.es> wrote:
> > Well, I'm not completely sure, but I think there is
> > a difference. Tell me if
> > I am wrong but I think you have to configure the
> > clock source since there is
> > no switch providing it. That command is there under
> > the same link.
> >
> > -----Mensaje original-----
> > De: Brown, Nelson [mailto:Nelson.Brown@NASD.com]
> > Enviado el: viernes, 01 de febrero de 2002 20:25
> > Para: ccielab@groupstudy.com
> > Asunto: RE: ATM with back to back routers
> >
> >
> > There's nothing special about PVCs between routers,
> > as opposed to having a
> > switch in-between. The PVC configuration task list
> > from the below article
> > will get you there. It worked for me.
> >
> > -----Original Message-----
> > From: Manny Gonzalez [mailto:gonzalu@nyp.org]
> > Sent: Friday, February 01, 2002 2:09 PM
> > To: Virnoche, Phil
> > Cc: ccielab@groupstudy.com
> > Subject: Re: ATM with back to back routers
> >
> >
> > Did you try this? (watch for wrap)
> >
> >
>http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_
> > c/wcdatm.htm
> >
> >
> >
> > "Virnoche, Phil" wrote:
> > >
> > > G-morning gang,...
> > >
> > > Cisco once had a very nice paper that demonstrated
> > how to set up an ATM
> > PVC
> > > between two routers, but I can't seem to find it
> > anymore.... Anyone help
> > > with a link, or sample configs???
> > >
> > > TIA !!!
> > >
> > > Philip G. Virnoche CCNP
> > > Sr. Network Engineer - (the late) AT&T Fixed
> > Wireless
> > > phone: 425.580.5239
> > > cell: 206.601.3134
> > > "Before you criticize someone, you should walk a
> > mile in their shoes.That
> > > way, when you criticize them, you are a mile away
> > from them ...and you
> > have
> > > their shoes."
> > >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 13:46:12 GMT-3