From: Jeff Kesemeyer (jkesemey@xxxxxxxxxxxxx)
Date: Thu Jan 10 2002 - 20:36:13 GMT-3
In the past you were required to make a diagram and there was a specific
type or format that people used. Crease 3" on each side for addresses,
diagram in middle, color pencils, templates, etc...
I practiced with making that diagram for months and then took the one
day. Since I no longer had to make a diagram I "saved" that time for
other important tasks like searching for which router had which address
on it.
I know next time I will make an address chart that I have heard that
others make for summarizing.
Now that this is no longer a requirement what is the census on
diagramming now?
Jeff Kesemeyer
CCNP, CCDP, MCSE, CNE
www.bradshawlabs.com
"Your CCIE Rack Rental Source"
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Lopez, James
Sent: Thursday, January 10, 2002 5:56 PM
To: 'EA Louie'; ccielab@groupstudy.com
Subject: RE: at the lab exam
All of these are great suggestions but does anyone have any ideas on the
best way to make your diagram?
I've heard it go both ways, are we allowed to bring colored pencils?
TIA,
-----Original Message-----
From: EA Louie [mailto:elouie@yahoo.com]
Sent: Thursday, January 10, 2002 3:33 PM
To: ccielab@groupstudy.com
Subject: Re: at the lab exam
great tool - thanks for sharing it - I'll use it on Tuesday
-e-
----- Original Message -----
From: "Brian Dennis" <brian@5g.net>
To: <ccielab@groupstudy.com>
Sent: Thursday, January 10, 2002 1:14 PM
Subject: RE: at the lab exam
> You also could make a sort of table to use while reading over the lab.
Mark
> down which devices need to be configured for each section. Then as you
> do the sections mark off (i.e. circle) what devices have been done.
> See
below:
>
> Device R1 R2 R3 R4 R5 Cat5
> Section
> 1.1 x x
> 1.2 x x x x
> 1.3 x x
> 2.1 x x
>
>
> A student of mine came up with this idea and I thought it was pretty
> cool.
>
> Brian Dennis, CCIE #2210 (R&S)(ISP/Dial) CCSI #98640
> 5G Networks, Inc.
> brian@5g.net
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Mas Kato
> Sent: Thursday, January 10, 2002 12:44 PM
> To: yusman@mastersystem.co.id
> Cc: ccielab@groupstudy.com
> Subject: RE: at the lab exam
>
>
> [demime could not interpret encoding binary - treating as plain text]
> I would suggest reading through the whole assignment not just once,
> but twice before charging in. On the first pass, look for issues and
> order dependencies. On the second pass look for absolutes--absolute
> values to be used, ranges to be covered, etc.--note these and then go
> for it!
>
> Best of luck,
>
> Mas Kato
> https://ecardfile.com/id/mkato
>
> > Yusman@mastersystem.co.id at the lab exam
> > ccielab@groupstudy.comDate:
Thu,
> 10 Jan 2002 18:31:05 +0700
> >Reply-To: Yusman@mastersystem.co.id
> >
> >For the first attempt lab exam, what is the best, read the whole lab
> >instruction then do the lab or read per section task then do the
> >test, without wasting the time
> >
> >Thanks for the opinion
> ------------------------------------------------------------
> Speed Racer's Official Virtual Pit Stop.
> http://www.speedracerdsl.com/speedracer/
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:23 GMT-3