From: Bhisham Bajaj (bhishambajaj@xxxxxxxxx)
Date: Thu Jan 03 2002 - 11:07:06 GMT-3
It should work
All u have to do is to add the command (clockrate
64000) to the inter face that has the rs232 fc cable
U can use the (show controllers serial xxx ) to
this I s serial inter face with a v.35 dce cable and
inter clockrate is 64000
RA#sh controllers serial 0
HD unit 0, idb = 0x93838, driver structure at 0x97BD0
buffer size 1524 HD unit 0, V.35 DCE cable, clockrate
64000 ************
cpb = 0x22, eda = 0x2050, cda = 0x2064
RX ring with 32 entries at 0x222000
00 bd_ptr=0x2000 pak=0x09CEF8 ds=0x236DA0 status=80
pak_size=72
01 bd_ptr=0x2014 pak=0x09CB98 ds=0x236030 status=80
pak_size=22
02 bd_ptr=0x2028 pak=0x09C9E8 ds=0x235978 status=80
pak_size=277
03 bd_ptr=0x203C pak=0x09C838 ds=0x2352C0 status=80
pak_size=277
04 bd_ptr=0x2050 pak=0x09C688 ds=0x234C08 status=80
pak_size=72
05 bd_ptr=0x2064 pak=0x09C328 ds=0x233E98 status=80
pak_size=72
this I s serial inter face with a v.232 dce cable and
inter clockrate is 64000
RA#sh controllers serial 1
HD unit 1, idb = 0x9EA60, driver structure at 0xA2DF8
buffer size 1524 HD unit 1, RS-232 DCE cable,
clockrate 64000
cpb = 0x23, eda = 0xE1A4, cda = 0xE1B8
RX ring with 32 entries at 0x23E000
00 bd_ptr=0xE000 pak=0x0A7C10 ds=0x2512C0 status=80
pak_size=22
01 bd_ptr=0xE014 pak=0x0A7A60 ds=0x250C08 status=80
pak_size=72
02 bd_ptr=0xE028 pak=0x0A78B0 ds=0x250550 status=80
pak_size=22
03 bd_ptr=0xE03C pak=0x0A7700 ds=0x24FE98 status=80
pak_size=72
04 bd_ptr=0xE050 pak=0x0A7550 ds=0x24F7E0 status=80
pak_size=22
05 bd_ptr=0xE064 pak=0x0A73A0 ds=0x24F128 status=80
pak_size=72
Reg
Bhisham
--- Chris Allen <chris.allen@callisma.com> wrote:
> Hold On, Don't Jump..... Can you post the output
> from "sho controllers s0"
> from both routers.... thanks..
>
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com]On Behalf Of
> Wen Jia Yang
> Sent: Thursday, January 03, 2002 8:33 AM
> To: ccielab@groupstudy.com
> Subject: back to back problem,I am going to kill
> myself!
>
>
> routerA and routerB are back to back,I use rs-232
> cables,i am sure
>
> clock rate is set,clock rate 64000.
>
> Anyone offer a hand?I am going to kill myself:((((
>
>
> RouterA#sh int s0
> Serial0 is down, line protocol is down
> Hardware is HD64570
> Internet address is 192.1.1.1/24
> MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely
> 255/255, load
>
> 1/255
> Encapsulation HDLC, loopback not set, keepalive
> set (10 sec)
> Last input 00:01:09, output never, output hang
> never
> Last clearing of "show interface" counters
> 00:03:18
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0
> drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 16 packets input, 1461 bytes, 0 no buffer
> Received 16 broadcasts, 0 runts, 0 giants, 0
> throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0
> ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 7 interface
> resets
> 0 output buffer failures, 0 output buffers
> swapped out
> 0 carrier transitions
> DCD=down DSR=up DTR=up RTS=up CTS=up
>
> RouterA#sh cdp nei
> Capability Codes: R - Router, T - Trans Bridge, B -
> Source Route Bridge
> S - Switch, H - Host, I - IGMP, r
> - Repeater
>
> Device ID Local Intrfce Holdtme
> Capability Platform
>
> Port ID
>
> RouterB#sh int s0
> Serial0 is up, line protocol is down
> Hardware is HD64570
> Internet address is 192.1.1.2/24
> MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely
> 255/255, load
>
> 1/255
> Encapsulation HDLC, loopback not set, keepalive
> set (10 sec)
> Last input 00:36:25, output 00:00:05, output hang
> never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0
> drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 862 packets input, 52988 bytes, 0 no buffer
> Received 701 broadcasts, 0 runts, 0 giants, 0
> throttles
> 46 input errors, 1 CRC, 0 frame, 0 overrun, 2
> ignored, 0 abort
> 1745 packets output, 120424 bytes, 0 underruns
> 0 output errors, 0 collisions, 83 interface
> resets
> 0 output buffer failures, 0 output buffers
> swapped out
> 90 carrier transitions
> DCD=up DSR=up DTR=up RTS=up CTS=up
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:15 GMT-3