From: Brad Ellis (bellis@xxxxxxxxxxxxxx)
Date: Tue Dec 18 2001 - 12:58:51 GMT-3
Gordon,
It's an overpriced paperweight. You could send it back to Olicom, but
they'll charge you a couple thousand to fix it (unless it's under warranty)!
You can't get smartnet, because it's not Cisco. Try to send it back to the
person you purchased it from. If you cant, here's a few things you can do
with it:
1) Leave it plugged in, turned on, and try to heat a small bedroom
2) Put it in a box, put wrapping paper and a bow on it, and give it to your
mother-in-law for a christmas present
3) Use it in the bathroom as a stepping-stool for a youngster
4) Try convincing a cisco TAC specialist, that it is, in fact, a Cisco 3900
under smartnet
5) EBAY
(I'm kidding about the (5) things above, fyi)
thanks,
-Brad Ellis
CCIE#5796 (R&S / Security)
Network Learning Inc
bellis@ccbootcamp.com
----- Original Message -----
From: "Gordon Olson" <gordonolson@yahoo.com>
To: <ccielab@groupstudy.com>
Sent: Tuesday, December 18, 2001 12:01 AM
Subject: 3920\Olicom OC-8600 will not boot
> I have an Olicom OC-8600 runs the 3920 IOS. I get he
> following error when trying to boot it.
>
> Looking for any suggestions, I have recently opened
> the switch to see if anything was loose, nothing
> appears to be. Thanks in advance for your input.
>
> BootStrap Firmware v2.2, Copyright 1996-1997
> - Initiating bootstrapping sequence.
> - Boot image integrity check...Passed.
> - Control transferred to boot process.
>
> Boot Firmware (Phase II) v2.1
> - Relocating main image to
> DRAM.................................................
> .........................................................Done.
> - Main image integrity check...succeeded.
> - Control transferred to main process.
> - Bypassing diagnostics.
>
> System Software Version 02.54H, Copyright 1994-1997.
> System started on Sun. September 16, 2001 06:21:13
> 8 Megabytes System memory
> 2 Megabytes Network memory
> - Initialization started
> - Change NVRAM size from 0x0 to 0x20000
> - failed to change NVRAM size: malloc failed
> - NVRAM size is still 0x0
> - Failed to upgrade to bigger File System
> - File system initialized
> - System temperature is within safe operating levels
> - Checking file system integrity
> - Warmboot initialization started
> WARNING: CrossFire Stack : Sub-directory creation
> failed
> No Such File or Directory
> WARNING: Unable to Write Port Config Data for port 1,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 2,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 3,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 4,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 5,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 6,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 7,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 8,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 9,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 10,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 11,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 12,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 13,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 14,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 15,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 16,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 17,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 18,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 19,
> rc=-300
> Failed writing to NVRAM
> WARNING: Unable to Write Port Config Data for port 20,
> rc=-300
> Failed writing to NVRAM
> - LAN ports detected:
> - RJ-45 Token Ring: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
> 15 16 17 18 19 20
> - Initializing Ports: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
> 15 16 17 18 19 20
> - Initializing system address table
>
> WARNING: Diagnostics failed to store information.
> WARNING: CrossFire Stack: Sub-directory creation
> failed
> No Such File or Directory
> - System entering stand-alone mode
> - Local box number: 1
> CrossFire Token-Ring Switch initiating bootp requests
> on one or more VLANs
> WARNING: Control box (1) failed NV Ram VTP
> configuration store
> FATAL SYSTEM ERROR: vtp_activate: bad return 42 from
> vtp_download_info
>
>
>
> =====
> Thank you,
>
> Gordon Olson
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:44 GMT-3