From: michael robertson (michael_w_2ca@xxxxxxxx)
Date: Thu Nov 29 2001 - 20:07:12 GMT-3
Hi, Waters,
I have done lots of times with ATM esi-address, but
never assign my own nsap address. As whenever I assign
a specific NSAP address, the NSAP prefix ( 13 bytes)
should be from atm switch. So I get the same default
cisco lightstream prefix for my NSAP address and put
suffix ( 7 byres ). i.e. 111111111111.00, But I don't
know why that I never get this work. I think all other
configuration are correct.
I have done it in CLIP and map svc etc. Never get it
work. Can you explain me why?
regards
michael
--- "Waters, Kivas (UK72)"
<Kivas.Waters@Honeywell.com> wrote:
> Here is a summary I did of the different ATM configs
> that I suspect we may
> be asked. Please note that I have not paid carefull
> attention to the use of
> the ESI/NSAP address and PVC 0/16. Therefore these
> configs may show my
> configuring an NSAP address in addition to standard
> ILMI PVC and ESI addres
> which is not required. Also, I have used
> subinterfaces which are not
> strictly a requirement. If you see any other
> oddities, please let me know!
>
> ...
>
>
> ATM PVC - RFC 1483
>
----------------------------------------------------------------------------
> --
>
> Rack1R6(config)#
> interface ATM6/0
> no atm ilmi-keepalive
> ip address 68.6.6.6 255.0.0.0
> pvc ccie 3/107
> encapsulation aal5snap
> protocol ip 68.8.8.8 broadcast
>
>
----------------------------------------------------------------------------
> --
>
> Rack1R8(config)#
> interface ATM3/0
> no atm ilmi-keepalive
> ip address 68.8.8.8 255.0.0.0
> pvc ccie 3/107
> encapsulation aal5snap
> protocol ip 68.6.6.6 broadcast
>
>
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
>
>
> ATM PVC - RFC 1577
>
----------------------------------------------------------------------------
> --
>
> Rack1R6(config)#
> interface ATM6/0
> ip address 68.6.6.6 255.0.0.0
> no atm ilmi-keepalive
> pvc 0/32
> inarp 10
> broadcast
> encapsulation aal5snap
> oam-pvc manage
> oam retry 3 3 3
>
>
----------------------------------------------------------------------------
> --
>
> Rack1R8(config)#
> interface ATM3/0
> ip address 68.8.8.8 255.0.0.0
> no atm ilmi-keepalive
> pvc 0/32
> inarp 10
> broadcast
> encapsulation aal5snap
> ! OAM F5 management is optional
> oam-pvc manage
> oam retry 3 3 3
>
>
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
>
>
> ATM SVC - RFC 1483
>
----------------------------------------------------------------------------
> --
>
> Rack1R6(config)#
> interface ATM6/0
> no ip address
> no atm ilmi-keepalive
> !The ILMI keepalive is used like the FR LMI and is
> used to determine
> interface
> !signalling health. It can be turned on or off
> depending on SNMP &
> ATM NSAP prefix
> !support
> pvc 0/16 ilmi
> !Configuring the ILMI is not requried in this
> example as the
> complete NSAP address is defined
> !on the ATM interface. If we wanted to just
> specify the ESI part
> then configuring the ILMI
> !makes more sense.
>
> pvc 0/5 qsaal
> !
> !
> interface ATM6/0.10 multipoint
> ip address 68.6.6.6 255.0.0.0
> atm nsap-address
> 47.112233445566778899001122.666666666666.00
> !The following command can be used with ILMI 0/16
> instead of
> configuring the full ATM NSAP
> !address "atm esi-address 666666666666.00"
>
> svc nsap
> 47.112233445566778899001122.888888888888.00
> protocol ip 68.8.8.8 broadcast
> encapsulation aal5snap
> broadcast
>
>
----------------------------------------------------------------------------
> --
>
> Rack1R8(config)#
> interface ATM3/0
> no ip address
> no atm ilmi-keepalive
> pvc 0/5 qsaal
> !
> pvc 0/16 ilmi
> !
> !
> interface ATM3/0.10 multipoint
> ip address 68.8.8.8 255.0.0.0
> atm nsap-address
> 47.112233445566778899001122.888888888888.00
> !
> svc nsap
> 47.112233445566778899001122.666666666666.00
> protocol ip 68.6.6.6 broadcast
> encapsulation aal5snap
> broadcast
>
>
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
----------------------------------------------------------------------------
> --
>
>
>
> ATM SVC - RFC 1577
>
----------------------------------------------------------------------------
> ---
>
> Rack1R6(config)#
> interface ATM6/0
> no ip address
> atm ilmi-keepalive
> pvc 0/5 qsaal
> !
> pvc 0/16 ilmi
> !
> !
> interface ATM6/0.10 multipoint
> ip address 68.6.6.6 255.0.0.0
> atm nsap-address
> 47.666600006666000066660000.666666666666.00
> atm arp-server nsap
> 47.666600006666000066660000.888888888888.00
>
>
----------------------------------------------------------------------------
> ---
>
> Rack1R8(config)#
> interface ATM3/0
> no ip address
> atm ilmi-keepalive
> pvc 0/5 qsaal
> !
> pvc 0/16 ilmi
> !
> !
> interface ATM3/0.10 multipoint
> ip address 68.8.8.8 255.0.0.0
> atm nsap-address
> 47.666600006666000066660000.888888888888.00
> atm arp-server self
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:26 GMT-3