From: Murphy, Brennan (Brennan_Murphy@xxxxxxx)
Date: Wed Nov 14 2001 - 17:29:58 GMT-3
since this circuit only used 1 E1, i removed the IMA
config and placed the pvc config under a subinterface
on the physical atm interface and everything started
working.
thanks for the responses and assistance!
-----Original Message-----
From: Murphy, Brennan [mailto:Brennan_Murphy@nai.com]
Sent: Wednesday, November 14, 2001 12:24 PM
To: 'Tao Yang'; ccielab@groupstudy.com
Subject: RE: ATM troubles--show commands and config
Thanks for pointing out the bug Tao but we are unable to pass traffic
which is inconsistent with the bug description.
Here is the config on the 3640 router followed by some show commands
related to ATM troubleshooting:
The atm config:
interface ATM1/0
description ATM interface to Worldcom
no ip address
shutdown
no atm ilmi-keepalive
ima-group 0
scrambling-payload
impedance 120-ohm
!
interface ATM1/1
no ip address
no atm ilmi-keepalive
ima-group 0
scrambling-payload
impedance 120-ohm
!
interface ATM1/2
no ip address
shutdown
no atm ilmi-keepalive
scrambling-payload
impedance 120-ohm
!
interface ATM1/3
no ip address
shutdown
no atm ilmi-keepalive
scrambling-payload
impedance 120-ohm
!
interface ATM1/IMA0
no ip address
no atm ilmi-keepalive
!
interface ATM1/IMA0.1 point-to-point
description PVC to Sydney 512 SCR
ip address x.x.191.14 255.255.255.252
pvc 1/152
protocol ip x.x.191.13 broadcast
vbr-nrt 1024 512 1000
encapsulation aal5snap
!
honrt1>sh ip int brie
Interface IP-Address OK? Method Status
Protocol
FastEthernet0/0 x.x.178.46 YES NVRAM administratively down
down
ATM1/0 unassigned YES NVRAM administratively down
down
ATM1/1 unassigned YES NVRAM up
down
ATM1/2 unassigned YES NVRAM administratively down
down
ATM1/3 unassigned YES NVRAM administratively down
down
ATM1/IMA0 unassigned YES NVRAM up
down
ATM1/IMA0.1 x.x.191.14 YES NVRAM up
down
honrt1#sh cont atm 1/1
Interface ATM1/1 is up
Hardware is ATM E1
LANE client MAC address is 0006.d764.c231
hwidb=0x61BA8330, ds=0x61BC0EF8
slot 1, unit 1, subunit 1
rs8234 base 0x3C800000, slave base 0x3C800000
rs8234 ds 0x61BC0EF8
SBDs - avail 2048, guaranteed 1, unguaranteed 2047, starved 0
Seg VCC table 3C80DD80, Shadow Seg VCC Table 61BDD05C, VCD Table 61BF3088
Schedule table 3C818D80, Shadow Schedule table 61BF90B4, Size 7CD
RSM VCC Table 3C86E280, Shadow RSM VCC Table 61C3E4C4
VPI Index Table 3C82B800, VCI Index Table 3C82E280
Bucket2 Table 3C822A00, Shadow Bucket2 Table 61BFB014
MCR Limit Table 3C822E00, Shadow MCR Table 61BFCC40
ABR template 3C823000, Shadow template 6189CBFC
RM Cell RS Queue 3C82C280
Queue TXQ Addr Pos StQ Addr Pos
0 UBR CHN0 3C828000 1 031671C0 0
1 UBR CHN1 3C828400 0 031679C0 0
2 UBR CHN2 3C828800 0 031681C0 0
3 UBR CHN3 3C828C00 0 031689C0 0
4 VBR/ABR CHN0 3C829000 0 031691C0 0
5 VBR/ABR CHN1 3C829400 0 031699C0 0
6 VBR/ABR CHN2 3C829800 0 0316A1C0 0
7 VBR/ABR CHN3 3C829C00 0 0316A9C0 0
8 VBR-RT CHN0 3C82A000 0 0316B1C0 0
9 VBR-RT CHN1 3C82A400 0 0316B9C0 0
10 VBR-RT CHN2 3C82A800 0 0316C1C0 0
11 VBR-RT CHN3 3C82AC00 0 0316C9C0 0
12 SIG 3C82B000 0 0316D1C0 0
13 VPD 3C82B400 0 0316D9C0 0
Queue FBQ Addr Pos RSQ Addr Pos
0 OAM 3C87A280 255 0316E280 0
1 UBR CHN0 3C87B280 0 0316F280 0
2 UBR CHN1 3C87C280 0 03170280 0
3 UBR CHN2 3C87D280 0 03171280 0
4 UBR CHN3 3C87E280 0 03172280 0
5 VBR/ABR CHN0 3C87F280 255 03173280 0
6 VBR/ABR CHN1 3C880280 0 03174280 0
7 VBR/ABR CHN2 3C881280 0 03175280 0
8 VBR/ABR CHN3 3C882280 0 03176280 0
9 VBR-RT CHN0 3C883280 0 03177280 0
10 VBR-RT CHN1 3C884280 0 03178280 0
11 VBR-RT CHN2 3C885280 0 03179280 0
12 VBR-RT CHN3 3C886280 0 0317A280 0
13 SIG 3C887280 0 0317B280 0
SAR Scheduling channels: -1 -1 -1 -1 -1 -1 -1 -1
Part of IMA group 0
Link 1 IMA Info:
group index is 0
Tx link id is 1, Tx link state is unusableNoGivenReason
Rx link id is 99, Rx link state is unusableFailed
Rx link failure status is lodsFailure,
0 tx failures, 3 rx failures
Link 1 Framer Info:
framing is Multiframe-CRC4, line code is HDB3, impedance is 120 ohm
clock src is line, payload-scrambling is enabled, no loopback
line status is 0x1; or no alarm.
port is active, link is available
214720546 idle rx, 0 correctable hec rx, 0 uncorrectable hec rx
20658 cells rx, 214356882 cells tx, 35 rx fifo overrun.
Link (1):DS1 MIB DATA:
Data in current interval (622 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 52 15 minute intervals):
8191 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 90 Unavail Secs
SAR counter totals across all links and groups:
0 cells output, 0 cells stripped
0 cells input, 32 cells discarded, 0 AAL5 frames discarded
0 pci bus err, 0 dma fifo full err, 0 rsm parity err
0 rsm syn err, 0 rsm/seg q full err, 0 rsm overflow err
0 hs q full err, 0 no free buff q err, 0 seg underflow err
0 host seg stat q full err
honrt1#sh atm int atm1/1
Interface ATM1/1:
AAL enabled: AAL5 , Maximum VCs: 256, Current VCCs: 0
Maximum Transmit Channels: 0
Max. Datagram Size: 4496
PLIM Type: E1, Framing is E1-CRC4, TX clocking: LINE
Cell-payload scrambling: ON
0 input, 0 output, 0 IN fast, 0 OUT fast, 0 out drop
Avail bw = 2000
Config. is ACTIVE
honrt1#sh atm int atm1/ima0
Interface ATM1/IMA0:
AAL enabled: AAL5 , Maximum VCs: 256, Current VCCs: 1
Maximum Transmit Channels: 0
Max. Datagram Size: 4496
PLIM Type: E1 IMA, Framing is E1-CRC4, TX clocking: IMA CTC
0 input, 0 output, 0 IN fast, 0 OUT fast, 0 out dropVBR-NRT : 512
Avail bw = 3488
Config. is ACTIVE
honrt1#sh atm pvc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells
Sts
1/IMA0.1 4 1 152 PVC SNAP VBR 1024 512 1000
UP
honrt1#
honrt1#sh int atm1/ima0
ATM1/IMA0 is up, line protocol is down
Hardware is ATM IMA
MTU 4470 bytes, sub MTU 4470, BW 4000 Kbit, DLY 20000 usec,
reliability 5/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5
256 maximum active VCs, 1 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output 13:14:17, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1 packets output, 32 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
honrt1#sh control atm1/ima0
Interface ATM1/IMA0 is up
Hardware is ATM IMA
LANE client MAC address is 0006.d764.c230
hwidb=0x62090034, ds=0x61BC0EF8
slot 1, unit 0, subunit 0
rs8234 base 0x3C800000, slave base 0x3C800000
rs8234 ds 0x61BC0EF8
SBDs - avail 2048, guaranteed 1, unguaranteed 2047, starved 0
Seg VCC table 3C80DD80, Shadow Seg VCC Table 61BDD05C, VCD Table 61BF3088
Schedule table 3C818D80, Shadow Schedule table 61BF90B4, Size 7CD
RSM VCC Table 3C86E280, Shadow RSM VCC Table 61C3E4C4
VPI Index Table 3C82B800, VCI Index Table 3C82E280
Bucket2 Table 3C822A00, Shadow Bucket2 Table 61BFB014
MCR Limit Table 3C822E00, Shadow MCR Table 61BFCC40
ABR template 3C823000, Shadow template 6189CBFC
RM Cell RS Queue 3C82C280
Queue TXQ Addr Pos StQ Addr Pos
0 UBR CHN0 3C828000 1 031671C0 0
1 UBR CHN1 3C828400 0 031679C0 0
2 UBR CHN2 3C828800 0 031681C0 0
3 UBR CHN3 3C828C00 0 031689C0 0
4 VBR/ABR CHN0 3C829000 0 031691C0 0
5 VBR/ABR CHN1 3C829400 0 031699C0 0
6 VBR/ABR CHN2 3C829800 0 0316A1C0 0
7 VBR/ABR CHN3 3C829C00 0 0316A9C0 0
8 VBR-RT CHN0 3C82A000 0 0316B1C0 0
9 VBR-RT CHN1 3C82A400 0 0316B9C0 0
10 VBR-RT CHN2 3C82A800 0 0316C1C0 0
11 VBR-RT CHN3 3C82AC00 0 0316C9C0 0
12 SIG 3C82B000 0 0316D1C0 0
13 VPD 3C82B400 0 0316D9C0 0
Queue FBQ Addr Pos RSQ Addr Pos
0 OAM 3C87A280 255 0316E280 0
1 UBR CHN0 3C87B280 0 0316F280 0
2 UBR CHN1 3C87C280 0 03170280 0
3 UBR CHN2 3C87D280 0 03171280 0
4 UBR CHN3 3C87E280 0 03172280 0
5 VBR/ABR CHN0 3C87F280 255 03173280 0
6 VBR/ABR CHN1 3C880280 0 03174280 0
7 VBR/ABR CHN2 3C881280 0 03175280 0
8 VBR/ABR CHN3 3C882280 0 03176280 0
9 VBR-RT CHN0 3C883280 0 03177280 0
10 VBR-RT CHN1 3C884280 0 03178280 0
11 VBR-RT CHN2 3C885280 0 03179280 0
12 VBR-RT CHN3 3C886280 0 0317A280 0
13 SIG 3C887280 0 0317B280 0
SAR Scheduling channels: -1 -1 -1 -1 -1 -1 -1 -1
ATM channel number is 0
link members are 0x3, active links are 0x0
Group status is blockedNe, 2 links configured,
Group Info: Configured links bitmap 0x3, Active links bitmap 0x0,
Tx/Rx IMA_id 0x10/0x63,
NE Group status is startUp,
frame length 0x80, Max Diff Delay 0,
1 min links, clock mode ctc, symmetry symmetricOperation, trl 0,
Group Failure status is startUpNe.
Test pattern procedure is disabled
SAR counter totals across all links and groups:
0 cells output, 0 cells stripped
0 cells input, 32 cells discarded, 0 AAL5 frames discarded
0 pci bus err, 0 dma fifo full err, 0 rsm parity err
0 rsm syn err, 0 rsm/seg q full err, 0 rsm overflow err
0 hs q full err, 0 no free buff q err, 0 seg underflow err
0 host seg stat q full err
honrt1#sh atm traff
0 Input packets
0 Output packets
0 Broadcast packets
0 Packets received on non-existent VC
0 Packets attempted to send on non-existent VC
0 OAM cells received
F5 InEndloop: 0, F5 InSegloop: 0, F5 InAIS: 0, F5 InRDI: 0
F4 InEndloop: 0, F4 InSegloop: 0, F4 InAIS: 0, F4 InRDI: 0
0 OAM cells sent
F5 OutEndloop: 0, F5 OutSegloop: 0, F5 OutRDI: 0
F4 OutEndloop: 0, F4 OutSegloop: 0, F4 OutRDI: 0
0 OAM cell drops
honrt1#sh atm map
Map list ATM1/IMA0.1pvc4 : PERMANENT
ip x.x.191.13 maps to VC 4, VPI 1, VCI 152, ATM1/IMA0.1
, broadcast
honrt1#
-----Original Message-----
From: Tao Yang [mailto:tyang@attcanada.ca]
Sent: Wednesday, November 14, 2001 11:45 AM
To: Murphy, Brennan; ccielab@groupstudy.com
Subject: Re: ATM troubles
Excerpt from Cisco:
"Before Cisco IOS. Software Release 12.0(11)S and 12.1(3)E, ATM physical
interfaces configured as a member of an IMA group could have a "line
protocol is down" status even though the IMA interface was up/up and passed
traffic without any problems. This state could occur on the Cisco 7200
router series because the ATM interfaces are the raw links, and all
protocol-related configuration is done on the virtual IMA interface. Cisco
Bug ID CSCdr22203 changed this default behavior on the 7200 router. On the
7500 and 3600 series, the line protocol status on the ATM physical
interfaces is brought up when the links are operational. "
----- Original Message -----
From: "Murphy, Brennan" <Brennan_Murphy@NAI.com>
To: <ccielab@groupstudy.com>
Sent: Wednesday, November 14, 2001 11:13 AM
Subject: OT: ATM troubles
> We're building out an ATM network and having trouble with a couple sites.
> We have Cisco 7200s in the hubs and 3600s with 4 port IMAs at the
> remote sites. I can loop the line on the 3600 and from the 7200 ping
> the local interface....the ping travels across the pvc to the 3600 and
> back. But when we normalize the circuit, we have interface up and
> line protocol down. The hub router is working fine with other PVCs.
> Anyone every have any problems with the 4 port IMA on an E1 circuit?
> Thanks
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:15 GMT-3