From: Chris Lilley (CLilley@xxxxxxxxxxxx)
Date: Tue Oct 23 2001 - 12:37:08 GMT-3
Ravi,
The either refers to the direction of the call. You would never have both
an inbound and outbound originated call on one line at the same time. The
either means your router could have placed or received the call.
Regards,
Chris
-----Original Message-----
From: Ravi [mailto:s_ravichandran@hotmail.com]
Sent: Tuesday, October 23, 2001 10:01 AM
To: Richard Gallagher; routerjocky; ccielab@groupstudy.com
Subject: Re: dialer load-threshold
Rich,
So, what is the answer for my example? will that bring up the second channel
or not?
Regards,
Ravi
----- Original Message -----
From: Richard Gallagher <rgallagh@cisco.com>
To: Ravi <s_ravichandran@hotmail.com>; routerjocky <elouie@yahoo.com>;
<ccielab@groupstudy.com>
Sent: Tuesday, October 23, 2001 12:24 PM
Subject: Re: dialer load-threshold
> Ravi,
>
> If one sides transmit rate reaches more than 128/255 x 64K then the the
second
> B channel will be bought up.
>
> Rich
>
> CCIE# 7211
>
> On Oct 23, 4:17pm, Ravi chatted about:
> > Subject:Re: dialer load-threshold
> > Still I am confused.
> >
> > Let us consider the following example.
> >
> > ppp multilink
> > dialer load-threshold 128 either
> >
> > 1) if the outbound load is 50k and inbound load is 46k, will this bring
up
> > the second bri?
> >
> > Regards,
> > Ravi
> >
> >
> >
> >
> >
> >
> > ----- Original Message -----
> > From: routerjocky <elouie@yahoo.com>
> > To: Ravi <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> > Sent: Tuesday, October 23, 2001 9:51 AM
> > Subject: Re: dialer load-threshold
> >
> >
> > > > Can you tell me What is the meaning of either?
> > > Hey, Ravi...
> > >
> > > it means either inbound and outbound
> > >
> > > >
> > > >
> > > >
> > > > Regards,
> > > > Ravi
> > > >
> > > > ----- Original Message -----
> > > > From: John Kim <albugkim@hotmail.com>
> > > > To: <s_ravichandran@hotmail.com>; <ccielab@groupstudy.com>
> > > > Sent: Tuesday, October 23, 2001 9:23 AM
> > > > Subject: Re: dialer load-threshold
> > > >
> > > >
> > > > > Ravi,
> > > > >
> > > > > The default is outbound and you can see that by sh run command.
> > > > >
> > > > > Thanks,
> > > > > John Kim
> > > > >
> > > > >
> > > > > >From: "Ravi" <s_ravichandran@hotmail.com>
> > > > > >Reply-To: "Ravi" <s_ravichandran@hotmail.com>
> > > > > >To: <ccielab@groupstudy.com>
> > > > > >Subject: dialer load-threshold
> > > > > >Date: Tue, 23 Oct 2001 09:08:50 -0400
> > > > > >
> > > > > >Hi,
> > > > > >
> > > > > >When entering dialer load threshold command, there are four
options.
> > > > > >
> > > > > >1) either
> > > > > >2) inbound
> > > > > >3) outbound
> > > > > >4) cr
> > > > > >
> > > > > >can anyone let me know what is cr? in other words, what is the
> > default?
> > > > > >
> > > > > >Also either means whether the addition of both inbound and
outbound
> > > > > >traffic?
> > > > > >
> > > > > >How can I verify?
> > > > > >
> > > > > >
> > > > > >Regards,
> > > > > >Ravi
This archive was generated by hypermail 2.1.4 : Thu Jun 20 2002 - 22:33:24 GMT-3