From: jonatale@xxxxxxxxxxxxx
Date: Tue Sep 11 2001 - 01:12:35 GMT-3
I respectfully disagree. I have set up ATM PVCs with Fore ATM Switches. I can't
speak for the LS.
I also wonder how the auto discovery would work if the switch, which it most
likely will, changes the VPI/VCIs within the PVC if the this is a router (I
assume you mean end end station and/or edge device) function.
Also, there does not need to be a switch to run ILMI [keepalives].
PLEASE correct me if I am wrong.
Thank you.
-Jonathan
Jeff Kesemeyer wrote:
> This is a router not a switch function, the router must be running 11.3 or
> better though.
> I do believe there needs to be a switch in the middle for the ilmi however.
>
> You only can do pvc's with back-to-back routers. You might want to check
> ebay for a lightstream 100 atm switch, should be able to get one around
> $600.
>
> What type of routers are you using for atm?
>
> Jeff Kesemeyer
> CCNP, CCDP, MCSE, CNE
> www.bradshawlabs.com
> "Your CCIE Rack Rental Source"
>
> -----Original Message-----
> From: jonatale@earthlink.net [mailto:jonatale@earthlink.net]
> Sent: Monday, September 10, 2001 2:50 AM
> To: Jeff Kesemeyer; Brian
> Cc: Nicholas Jaksec; CCIE
> Subject: Re: ATM Question
>
> does the switch need to be config'd to [provide] auto-discovery for this to
> work?
> can this would for router to router ATM?"Jeff Kesemeyer"
> <jkesemey@bellsouth.net>
>
> Brian <signal@shreve.net>
> T
> Jeff Kesemeyer wrote:
>
> > Thanks, you are correct just a bad habit I have for svc's.
> >
> > Jeff Kesemeyer
> > CCNP, CCDP, MCSE, CNE
> > www.bradshawlabs.com
> > "Your CCIE Rack Rental Source"
> >
> >
> > -----Original Message-----
> > From: Brian [mailto:signal@shreve.net]
> > Sent: Sunday, September 02, 2001 8:57 PM
> > To: Jeff Kesemeyer
> > Cc: Nicholas Jaksec; CCIE
> > Subject: RE: ATM Question
> >
> > Jeff,
> >
> > qsaal (0/5) is not needed for ilmi-auto-discovery, only
> > ilmi (0/16) is needed.
> >
> > Brian
> >
> > On Sun, 2 Sep 2001, Jeff Kesemeyer wrote:
> >
> > > Use ilmi-auto-discovery -
> > > configure ilmi and qsaal.
> > > Use show atm pvc or show atm vc to display the VPI/VCI of any
> PVC's the
> > > router discovers.
> > >
> > > interface ATM0/0
> > > atm pvc 1 0 16 ilmi
> > > ! Configs ilmi
> > > atm pvc 2 0 5 qsaal
> > > ! Configs qsaal
> > > atm ilmi-pvc-discovery
> > > ! Enables ilmi-pvc-discovery
> > >
> > >
> > > Jeff Kesemeyer
> > > CCNP, CCDP, MCSE, CNE
> > > www.bradshawlabs.com
> > > "Your CCIE Rack Rental Source"
> > >
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > > Nicholas Jaksec
> > > Sent: Sunday, September 02, 2001 7:35 PM
> > > To: CCIE
> > > Subject: ATM Question
> > >
> > >
> > > I am trying to setup and ATM connection and cannot determine the VPI/VCI
> > > values from the switch. How can I discover the VPI/VCI values from an
> ATM
> > > interface. Any help would be great, thanks !!
> > >
> > >
> > >
> > > ********************************************
> > > Nicholas R. Jaksec, CCNP, CCDP, MCSE+I, CNA
> > > Network Systems Engineer
> > > Lucent Worldwide Services
> > > One North Shore Center
> > > 12 Federal St. Suite 420
> > > Pittsburgh, Pa 15212
> > > Office: 412-330-6336 Fax: 412-323-7665
> > > Pager: 1-800-467-1467
> > > Email: jaksec@lucent.com
> > > ********************************************
> > > **Please read:http://www.groupstudy.com/list/posting.html
> > > **Please read:http://www.groupstudy.com/list/posting.html
> > -----------------------------------------------
> > I'm buying / selling used CISCO gear!!
> > email me for a quote
> >
> > Brian Feeny, CCIE #8036 Netjam, LLC
> > signal@netjam.net http://www.netjam.net
> > VISA/MC/AMEX/COD phone: 318-212-0245
> > 30 day warranty fax: 318-212-0246
> > **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:16 GMT-3