From: Paul Schultz (khyron@xxxxxxxxxxxxx)
Date: Fri Sep 07 2001 - 18:11:23 GMT-3
Frame relay switch only provides the DLCI to the physical interface, if
you're using point to point subinterfaces the router has no idea which
DLCI goes to which sub, which is why you must specify an
"interface-dlci" in the subint config.
On Fri, 7 Sep 2001, sanjay wrote:
> I disagree..the Frame Relay Switch provides the DLCI.
>
> -Sanjay
>
>
> ----- Original Message -----
> From: <John.K.Feuerherd@WellsFargo.COM>
> To: <ccienxtyear@hotmail.com>; <roger@securabyte.com>;
> <ccielab@groupstudy.com>
> Sent: Friday, September 07, 2001 12:28 PM
> Subject: RE: OSPF over Frame-Relay - Interface-DLCI vs. Map IP/Broadcas
>
>
> > For Frame-Relay Point-to-point sub interfaces you do need the "Frame-relay
> > interface-dlci" command. Otherwise how would the DLCI get assigned to that
> > interface.
> >
> > Here is how I understand it:
> > "Frame-Relay Interface-DLCI" assigns a DLCI to a particular interface.
> With
> > this command you are relying on INV-ARP to do the layer three to layer two
> > mapping for you. This is the only way that you can assign a DLCI to a
> > Point-to-Point sub interface.
> >
> > "Frame-relay map" with this command you are statically mapping the layer
> > three protocol to layer two(the DLCI). You can't use this command on a
> > point-to-pont sub interface, but rather only on multipoint and the
> physical
> > frame relay interface. I recommend doing this on the lab and not trusting
> > INV-ARP.
> >
> > As far as the "broadcast" statement after the map command, it is used for
> > enabling the forwarding of broadcast and multicast packets. This is needed
> > for the correct operation of some routing protocols.
> >
> > Hope that helps,
> >
> > JF
> >
> > -----Original Message-----
> > From: sanjay [mailto:ccienxtyear@hotmail.com]
> > Sent: Friday, September 07, 2001 11:44 AM
> > To: Roger Sohn; Ccielab (E-mail)
> > Subject: Re: OSPF over Frame-Relay - Interface-DLCI vs. Map IP/Broadcas
> >
> >
> > For point to point, theres no need for configuring DLCI's, MAP or
> Broadcast
> > statements.
> >
> > -Sanjay
> >
> >
> > ----- Original Message -----
> > From: "Roger Sohn" <roger@securabyte.com>
> > To: "Ccielab (E-mail)" <ccielab@groupstudy.com>
> > Sent: Friday, September 07, 2001 9:50 AM
> > Subject: OSPF over Frame-Relay - Interface-DLCI vs. Map IP/Broadcas
> >
> >
> > > I'm running OSPF over Frame-Relay in a hub and spoke
> > > configuration.(CCbootcamp labs) I've set up Router1(hub) to have
> > interface
> > > S0.1 (p2p) and interface S0.2(multipoint). For multipoint connections,
> > it's
> > > pretty easy because I just input map ip statements.
> > >
> > > But for my p2p connection, I'm having trouble understanding when I'm
> > > supposed to use the "frame-relay interface-dlci" , "frame-relay map ip",
> > or
> > > frame-relay map ip broadcast" statements on the hub and spokes. Can
> > anyone
> > > help shed some light on this?
> > >
> > > I've tried using a combination of all 3 types on both the hub and spoke,
> > and
> > > every time the hub and spoke are able to ping each other without any
> > > problems.
> > >
> > > -Roger
> > > **Please read:http://www.groupstudy.com/list/posting.html
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:15 GMT-3