From: jonatale@xxxxxxxxxxxxx
Date: Thu Aug 23 2001 - 02:40:32 GMT-3
interesting theory, sounds possible because if it did come up the spf tree woul
d be
hosed
the thing to do is check the debugs, not sure which one... BUT
i'd also agree with yves: as far as ccie prep -- better to know ospf/bgp cold (
this
is just an academic pursuit (not that that is bad))
Yves Fauser wrote:
> Hans,
>
> Sorry, but I can't really answer your question, but here is my guess.
> I guess this is something like a Database protection. The first spoke commes
up
> and builds an adjancency with the Hub Router. LSP's are exchanged, and a DR i
s
> elected. After that, the Database must be equal on both routers. Now if the
> second spoke comes up the Hub router gets broadcast net LSP's from the new sp
oke
> stating only one adjancency (with the Hub). From the other spoke it gets LSP'
s
> also only stating that there is one adjancency (with the Hub). I think to avo
id
> a Database corruption the Hub router does not accept the LSA's from the secon
d
> Spoke until all router on the broadcast net report the same adjacencies. But
> again, this is just a guess from me, and I did not test it in the Lab.
>
> Yves
>
> hans wrote:
>
> > Hi folks,
> >
> > I am not expecting the spoke can spoke loopback.
> >
> > In my case, on R2, I am not expecting to see R1's loopback and vice versa.
> >
> > I just want R1(hub) see loopbacks of both spokes (R2 and R3). However, I ca
n
> > not make it. Before R3 is up, R1(hub) can see R2's loopback(spoke) and vice
> > versa. But when I have another spoke turned up(R3), R1 can not see R2's
> > loopback and vice versa.
> >
> > My questionis: why on the hub(R1), I can see only one spoke. Is hub(R1)
> > supposed to see two spokes at the same time?
> >
> > Hans
> >
> > ----- Original Message -----
> > From: "Jason Sinclair" <sinclairj@powertel.com.au>
> > To: "'hans'" <yyao@sympatico.ca>; "Jason Sinclair"
> > <sinclairj@powertel.com.au>
> > Cc: <ccielab@groupstudy.com>
> > Sent: Wednesday, August 22, 2001 3:16 AM
> > Subject: RE: sis over frame relay
> >
> > > Hans,
> > >
> > > OK - perhaps the issue is that the DR is one of the spokes. Try changing
> > the
> > > isis priority on the hub to force it to be the DR. Also I cannot find the
> > > command to see the isis DR - does anyone know how to do this?
> > >
> > > Regards,
> > >
> > > Jason Sinclair
> > > Team Leader - NSG
> > > POWERTEL Limited
> > > Level 11, 55 Clarence Street, SYDNEY
> > > Phone: 61-2-8264-3820
> > > Mobile: 0416 105 858
> > > jasons@powertel.net.au
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: hans [mailto:yyao@sympatico.ca]
> > > Sent: Wednesday, 22 August 2001 17:02
> > > To: Jason Sinclair
> > > Cc: ccielab@groupstudy.com
> > > Subject: re: sis over frame relay
> > >
> > > Jason,
> > >
> > >
> > > Your configuration is correct. However, if the scenario has
> > > two spokes,
> > > problem arise.
> > >
> > > Here it is:
> > >
> > >
> > > R2/s0---302/203---s0/R1/s0---204/402---s0/R3
> > >
> > > Where 302 is dlci on R2, 203 is dlci on R1, 204 is dlci on
> > > R1 402 is dlci on
> > > R3.
> > >
> > > On the s0 of R1, there are two DLCIs connecting to R2 and R3
> > > respectively.
> > > R1 is the frame relay hub, R2 and R2 are spokes.
> > > Assume all the loopbacks of the three routers have been
> > > included in ISIS.
> > > I also have clns map configured.
> > >
> > > Before I turned up R3(or before I type in "frame relay map
> > > clns 402
> > > broadcast" on R3)
> > >
> > > R1and R2 can see each other's loopback.
> > >
> > > But the minute I turned up R3(put in frame map clns command
> > > on R3), on R1, I
> > > lost R2's loopback. On R2, I lost R1's loopback.
> > > However, R1 and R3 can see each other's loopbacks now.
> > >
> > > Following is my config:
> > >
> > > R1:
> > >
> > > interface Loopback0
> > > ip address 11.0.0.1 255.0.0.0
> > > ip router isis
> > > !
> > > interface Serial0
> > > ip address 2.2.2.1 255.255.255.248
> > > ip router isis
> > > encapsulation frame-relay
> > > frame-relay map clns 204 broadcast
> > > frame-relay map clns 203 broadcast
> > > frame-relay map ip 2.2.2.2 203 broadcast
> > > frame-relay map ip 2.2.2.3 204 broadcast
> > > no frame-relay inverse-arp
> > > frame-relay lmi-type cisco
> > > !
> > > router isis
> > > net 00.0002.1111.1111.1111.00
> > >
> > > R2:
> > >
> > > interface Loopback0
> > > ip address 22.0.0.1 255.255.255.0
> > > ip router isis
> > > !
> > > interface Serial0
> > > ip address 2.2.2.2 255.255.255.248
> > > ip router isis
> > > encapsulation frame-relay
> > > frame-relay map clns 302 broadcast
> > > frame-relay map ip 2.2.2.1 302 broadcast
> > > frame-relay map ip 2.2.2.3 302 broadcast
> > > no frame-relay inverse-arp
> > > frame-relay lmi-type cisco
> > > !
> > > router isis
> > > net 00.0002.2222.2222.2222.00
> > > !
> > >
> > >
> > > R3:
> > >
> > > interface Loopback0
> > > ip address 33.0.0.1 255.255.0.0
> > > ip router isis
> > > !
> > >
> > > interface Serial0
> > > ip address 2.2.2.3 255.255.255.248
> > > ip router isis
> > > encapsulation frame-relay
> > > frame-relay map clns 402 broadcast
> > > frame-relay map ip 2.2.2.1 402 broadcast
> > > frame-relay map ip 2.2.2.2 402 broadcast
> > > no frame-relay inverse-arp
> > > !
> > >
> > > router isis
> > > net 00.0002.3333.3333.3333.00
> > >
> > >
> > > show ip route on R1 before turning up R3:
> > > i L1 22.0.0.0 [115/20] via 2.2.2.2, Serial0
> > >
> > > show ip route on R1 after turning up R3:
> > > i L1 33.0.0.0 [115/20] via 2.2.2.3, Serial0
> > >
> > > We can see R2's loopback disappear from R1's routing table.
> > >
> > > Need your help on that.
> > >
> > > Hans
> > >
> > >
> > >
> > >
> > >
> > > ----- Original Message -----
> > > From: "Jason Sinclair" <sinclairj@powertel.com.au>
> > > To: "'hans'" <yyao@sympatico.ca>
> > > Sent: Tuesday, August 21, 2001 11:07 PM
> > > Subject: RE: isis over frame relay
> > >
> > >
> > > > Hans,
> > > >
> > > > I have set this up using the following:
> > > >
> > > >
> > > > RouterA--------------------F/R
> > > Switch--------------------------RouterB
> > > > DLCI 117 DLCI 118
> > > >
> > > > On routerA
> > > >
> > > > Router isis
> > > > Net 77.0000.7777.7777.7777.00
> > > >
> > > > Int s0
> > > > Ip address 172.16.1.1 255.255.255.252
> > > > Encaps frame-relay
> > > > Frame-relay lmi-type ansi
> > > > Frame-relay map clns 117 broad
> > > > Ip router isis
> > > >
> > > > On routerB
> > > >
> > > > Router isis
> > > > Net 88.0000.8888.8888.8888.00
> > > >
> > > > Int s0
> > > > Ip address 172.16.1.2 255.255.255.252
> > > > Encaps frame-relay
> > > > Frame-relay lmi-type ansi
> > > > Frame-relay map clns 118 broad
> > > > Ip router isis
> > > >
> > > >
> > > > I then get an adjacency formed. I can also get an adj on
> > > multipoint ints,
> > > > however NOT on point-to-point ints.
> > > >
> > > > Try this config without the rest of the config on your
> > > router and see if
> > > it
> > > > is OK.
> > > >
> > > > Regards,
> > > >
> > > > Jason Sinclair
> > > > Team Leader - NSG
> > > > POWERTEL Limited
> > > > Level 11, 55 Clarence Street, SYDNEY
> > > > Phone: 61-2-8264-3820
> > > > Mobile: 0416 105 858
> > > > jasons@powertel.net.au
> > > >
> > > >
> > > >
> > > > -----Original Message-----
> > > > From: hans [mailto:yyao@sympatico.ca]
> > > > Sent: Tuesday, 21 August 2001 17:50
> > > > To: Jason Sinclair
> > > > Subject: Re: isis over frame relay
> > > >
> > > > << File: config.zip >> Hi Jason,
> > > >
> > > > Here is my config.
> > > >
> > > >
> > > > Hans
> > > >
> > > >
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "Jason Sinclair" <sinclairj@powertel.com.au>
> > > > To: "'hans'" <yyao@sympatico.ca>
> > > > Sent: Tuesday, August 21, 2001 3:07 AM
> > > > Subject: RE: isis over frame relay
> > > >
> > > >
> > > > > Hans,
> > > > >
> > > > > Do you want to send me your configs on each router and I
> > > > will lab it this
> > > > > evening. I have done this over ATM which is also NBMA
> > > and
> > > > have had no
> > > > > problems.
> > > > >
> > > > > Regards,
> > > > >
> > > > > Jason Sinclair
> > > > > Team Leader - NSG
> > > > > POWERTEL Limited
> > > > > Level 11, 55 Clarence Street, SYDNEY
> > > > > Phone: 61-2-8264-3820
> > > > > Mobile: 0416 105 858
> > > > > jasons@powertel.net.au
> > > > >
> > > > >
> > > > >
> > > > > -----Original Message-----
> > > > > From: hans [mailto:yyao@sympatico.ca]
> > > > > Sent: Tuesday, 21 August 2001 17:11
> > > > > To: Jason Sinclair
> > > > > Subject: Re: isis over frame relay
> > > > >
> > > > > Hi Jason,
> > > > >
> > > > > I tried that, still not working.
> > > > >
> > > > > Any clues?
> > > > >
> > > > > Hans
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "Jason Sinclair" <sinclairj@powertel.com.au>
> > > > > To: "'hans'" <yyao@sympatico.ca>
> > > > > Sent: Tuesday, August 21, 2001 2:40 AM
> > > > > Subject: RE: isis over frame relay
> > > > >
> > > > >
> > > > > > Hans,
> > > > > >
> > > > > > You need to do the following:
> > > > > >
> > > > > > Frame relay map clns
> > > > > >
> > > > > > As you need to be able to transport CLNS PDU's to
> > > > > establish the peers.
> > > > > >
> > > > > > Let me know how you go.
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > > Jason Sinclair
> > > > > > Team Leader - NSG
> > > > > > POWERTEL Limited
> > > > > > Level 11, 55 Clarence Street, SYDNEY
> > > > > > Phone: 61-2-8264-3820
> > > > > > Mobile: 0416 105 858
> > > > > > jasons@powertel.net.au
> > > > > >
> > > > > >
> > > > > >
> > > > > > -----Original Message-----
> > > > > > From: hans [mailto:yyao@sympatico.ca]
> > > > > > Sent: Tuesday, 21 August 2001 16:27
> > > > > > To: ccielab@groupstudy.com
> > > > > > Subject: isis over frame relay
> > > > > >
> > > > > > Hi all,
> > > > > >
> > > > > > Does anyone know how to configure ISIS over frame
> > > relay?
> > > > > >
> > > > > > R2/s0----------s0/R1/s0------------s0.1/R3
> > > > > >
> > > > > > R1 is the hub, it use int s0 (2 DLCI) to connect with
> > > R2
> > > > > and
> > > > > > R3.
> > > > > >
> > > > > > I have router isis and net xxxxxx configured on all
> > > > three
> > > > > > routers.
> > > > > > I also have all the interfaces configured with ip
> > > router
> > > > > > isis.
> > > > > >
> > > > > > When I do show clns is-neighbors, I can not find
> > > > neighbors
> > > > > > at all.
> > > > > >
> > > > > >
> > > > > > Need your help on it.
> > > > > >
> > > > > >
> > > > > > Thanks,
> > > > > >
> > > > > > Hans
> > > > > > **Please
> > >
> > >
> > >
> > > **********************************************************************
> > > This email (including all attachments) is intended solely for the named
> > > addressee. It is confidential and may contain commercially sensitive
> > > information. If you receive it in error, please let us know by reply
> > email,
> > > delete it from your system and destroy any copies.
> > >
> > > This email is also subject to copyright. No part of it should be
> > reproduced,
> > > adapted or transmitted without the prior written consent of the copyright
> > owner.
> > >
> > > Emails may be interfered with, may contain computer viruses or other
> > defects
> > > and may not be successfully replicated on other systems. We give no
> > > warranties in relation to these matters. If you have any doubts about
> > > the authenticity of an email purportedly sent by us, please contact us
> > > immediately.
> > >
> > > **********************************************************************
> > > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:56 GMT-3