From: tom cheung (tkc9789@xxxxxxxxxxx)
Date: Wed Aug 22 2001 - 13:31:12 GMT-3
Looks like you're missing encap ppp and ppp authen chap on router1's dialer.
>From: "Michael Snyder" <msnyder@ldd.net>
>Reply-To: "Michael Snyder" <msnyder@ldd.net>
>To: <ccielab@groupstudy.com>
>Subject: Simple Trouble Shooting question about Dialer Profiles (vlab
>#3080)
>Date: Wed, 22 Aug 2001 10:46:48 -0500
>
>Hello list,
>
>I just got done with vlab 3080 at mentortech. I didn't get finished in
>time.
>I can't check my configs against the vlab solution because I used dialer
>profiles and the solution posted uses classic ddr.
>
>Here's my question, can someone take a quick look at my configs below and
>tell me if I missed anything. The remote lab was mainly just connecting
>router 1 and router 2 with bri 0. IOS ver 11.3
>
>What puzzles me is that, the dialer would dial out on command, ppp would
>authenticate.
>
>With the bri line up, I couldn't ping to or accross the upstream router. I
>checked the routes, the ip addresses, the correct subnet masks. The PPP
>and
>dialer side looked fine.
>
>Still no ping. What did I miss?
>
>
>
>
>Router1#ping 10.60.1.5
>
>Type escape sequence to abort.
>Sending 5, 100-byte ICMP Echos to 10.60.1.5, timeout is 2 seconds:
>.....
>Success rate is 0 percent (0/5)
>Router1#
>IP: s=10.60.1.5 (local), d=10.60.1.5 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.5 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.5 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.5 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.5 (Dialer10), len 100, sending
>Router1#sip c
> 10.0.0.0 0xFF000000 is variably subnetted, 5 subnets, 4 masks
>C 10.60.1.6 0xFFFFFFFF is directly connected, Dialer10
>C 10.60.1.0 0xFFFFFFF8 is directly connected, Dialer10
>C 10.60.1.8 0xFFFFFFFC is directly connected, Serial2.1
>C 10.60.0.64 0xFFFFFFC0 is directly connected, Ethernet0
>Router1#ping 10.60.1.6
>
>Type escape sequence to abort.
>Sending 5, 100-byte ICMP Echos to 10.60.1.6, timeout is 2 seconds:
>.....
>Success rate is 0 percent (0/5)
>Router1#
>IP: s=10.60.1.5 (local), d=10.60.1.6 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.6 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.6 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.6 (Dialer10), len 100, sending
>IP: s=10.60.1.5 (local), d=10.60.1.6 (Dialer10), len 100, sending
>
>
>
>
>
>
>
>
>Router 1
>
>username Router1 password 0 cisco
>username Router3 password 0 cisco
>
>interface BRI0
> no ip address
> encapsulation ppp
> dialer pool-member 44
> isdn switch-type basic-5ess
> ppp authentication chap
> ppp multilink
> no shutdown
>
>interface Dialer10
> ip address 10.60.1.5 255.255.255.248
> dialer remote-name Router3
> dialer string 3333
> dialer pool 44
> dialer-group 1
> no cdp enable
> no shutdown
>
>dialer-list 1 protocol ip list 101
>
>access-list 101 deny eigrp any any
>access-list 101 permit ip any 10.60.0.192 0.0.0.63
>access-list 101 permit ip any 10.60.1.0 0.0.0.7
>
>
>
>Router 3
>
>username Router1 password 0 cisco
>username Router3 password 0 cisco
>
>
>interface BRI0
> no ip address
> encapsulation ppp
> dialer pool-member 44
> isdn switch-type basic-5ess
> ppp authentication chap
> ppp multilink
> no shutdown
>
>interface Dialer10
> ip address 10.60.1.6 255.255.255.248
> encapsulation ppp
> dialer remote-name Router1
> dialer string 1111
> dialer pool 44
> dialer-group 10
> ppp authentication chap
> no shutdown
>
>
>dialer-list 10 protocol ip list 101
>
>access-list 101 deny eigrp any any
>access-list 101 permit ip any any
>**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:56 GMT-3