From: Albert Lu (albert_ccie@xxxxxxxxx)
Date: Tue Aug 07 2001 - 11:03:06 GMT-3
I've made some progress, and guess the correct isdn switch type.
Now, this is what I'm getting after a single ping. It looks like it's
telling me "Mandatory IE missing".
Could someone please take a look.
Thanks
Albert
RouterA#ping
Protocol [ip]: ip
Target IP address: 196.1.1.2
Repeat count [5]: 1
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 196.1.1.2, timeout is 2 seconds:
21:05:10: ISDN BR0: TX -> SETUP pd = 8 callref = 0x65
21:05:10: Bearer Capability i = 0x8890
21:05:10: Channel ID i = 0x83
21:05:10: Called Party Number i = 0x80, '2222'
21:05:10: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0xE5
21:05:10: Channel ID i = 0x89
21:05:10: ISDN BR0: RX <- SETUP pd = 8 callref = 0x4C
21:05:10: Sending Complete
21:05:10: Bearer Capability i = 0x8890
21:05:10: Channel ID i = 0x8A
21:05:10: Calling Party Number i = 0x0083, '2222'
21:05:10: Called Party Number i = 0x80, '2222'
21:05:10: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
21:05:10: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 2222
21:05:10: ISDN BR0: TX -> CONNECT pd = 8 callref = 0xCC
21:05:10: Channel ID i = 0x8A
21:05:10: ISDN BR0: RX <- CONNECT_ACK pd = 8 callref = 0x4C
21:05:10: ISDN BR0: RX <- ALERTING pd = 8 callref = 0xE5
21:05:10: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x65
21:05:10: .
Success rate is 0 percent (0/1)
RouterA# Cause i = 0x80E034 - Mandatory IE missing
21:05:10: ISDN BR0: RX <- CONNECT pd = 8 callref = 0xE5
21:05:10: Date/Time i = 0x0108060F18
21:05:10: ISDN BR0: RX <- RELEASE pd = 8 callref = 0xE5
21:05:10: Cause i = 0x80E034 - Mandatory IE missing
21:05:10: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 2222
21:05:10: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0x65
21:05:10: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0x4C
21:05:10: Cause i = 0x80E034 - Mandatory IE missing
21:05:10: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
21:05:10: ISDN BR0: TX -> RELEASE pd = 8 callref = 0xCC
21:05:10: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x4C
21:05:10: Cause i = 0x8090 - Normal call clearing
-----Original Message-----
From: DUNG H. LE [mailto:DHLE@sentara.com]
Sent: Tuesday, August 07, 2001 9:42 PM
To: albert_ccie@yahoo.com
Subject: Re: ISDN Problems
Abert,
Try to include your SPID1 and SPID2 under the interface configuration since
your are using basic-ni switch type. For example:
int bri 0
isdn spid1 0835866101 8358661
isdn spid2 0835866301 8358663
Hope this help.
Dung Le
CCIE 7878
>>> "Albert Lu" <albert_ccie@yahoo.com> 08/07/01 07:16AM >>>
Hello group,
I'm having a little problem with an isdn config. Basically, it's not dialing
through when I try to ping the other side. I'm sure the dialer map is
working, and my suspicion is that the isdn simulator (emutel lite) could be
misconfigured.
I have included my config, the "show isdn status" and "debug isdn q931"
output for reference.
Thanks in advance,
Albert
!
interface BRI0
ip address 196.1.1.1 255.255.255.0
no ip directed-broadcast
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer map ip 196.1.1.2 name RouterB broadcast 2222
dialer-group 1
isdn switch-type basic-ni
ppp authentication chap
ppp multilink
!
no ip classless
!
dialer-list 1 protocol ip permit
!
!
RouterA#sh isdn sta
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 65, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
RouterA#
RouterA#ping 196.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 196.1.1.2, timeout is 2 seconds:
18:35:08: ISDN BR0: TX -> SETUP pd = 8 callref = 0x10
18:35:08: Bearer Capability i = 0x8890
18:35:08: Channel ID i = 0x83
18:35:08: Keypad Facility i = '2222'
18:35:08: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x90
18:35:08: Cause i = 0x809D - Facility rejected or Special intercept,
cod
e undefined
18:35:08: ISDN BR0: Setup was rejected, cause = 1D.....
Success rate is 0 percent (0/5)
RouterA#
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:46 GMT-3