From: sanjay (ccienxtyear@xxxxxxxxxxx)
Date: Thu Jun 07 2001 - 18:35:42 GMT-3
I will reboot the sim. I do have the SIM configured correctly. Just a week
ago I was working on some practice labs and ISDN was working fine then (was
using the same spids and numbers). Will let you know if reloading SIM fixed
that problem. BTW- I have already reload both routers.
thanks
Sanjay
----- Original Message -----
From: "McCallum, Robert" <Robert.McCallum@let-it-be-thus.com>
To: "'sanjay'" <ccienxtyear@hotmail.com>
Sent: Thursday, June 07, 2001 2:17 PM
Subject: RE: ISDN Troubles
> Sanjay, Is the numbers correctly configured on your simulator? If so,
have
> you tried booting your simulator as well?
>
> -----Original Message-----
> From: sanjay [mailto:ccienxtyear@hotmail.com]
> Sent: 07 June 2001 22:07
> To: McCallum, Robert; ccielab@groupstudy.com
> Subject: Re: ISDN Troubles
>
>
> OK, heres the output from the other router. Both routers have been
> configured with each others name and same password. Also, there is
> dialer-list 1 protocol ip permit on both routers. They both seem to be
> having the same issues.
>
> r5#sh isdn stat
> Global ISDN Switchtype = basic-ni
> ISDN BRI0/0 interface
> dsl 0, interface ISDN Switchtype = basic-ni
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI = 65, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> Spid Status:
> TEI 64, ces = 1, state = 5(init)
> spid1 configured, spid1 sent, spid1 valid
> Endpoint ID Info: epsf = 0, usid = 70, tid = 1
> TEI 65, ces = 2, state = 5(init)
> spid2 configured, spid2 sent, spid2 valid
> Endpoint ID Info: epsf = 0, usid = 70, tid = 2
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Activated dsl 0 CCBs = 0
> The Free Channel Mask: 0x80000003
> Total Allocated ISDN CCBs = 0
> r5#
>
>
>
> !
> interface BRI0/0
> ip address 192.168.1.1 255.255.255.0
> no ip directed-broadcast
> encapsulation ppp
> dialer map ip 192.168.1.2 name r3 broadcast 8895101
> dialer load-threshold 1 outbound
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 5201 8895201
> isdn spid2 5202 8895202
> ppp authentication chap
> ppp multilink
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
>
> 00:04:47: BRI0/0 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.2)
> 00:04:47: BRI0/0 DDR: Attempting to dial 8895101
> 00:04:47: BRI0/0: wait for isdn carrier timeout, call id=0x8001
> 00:04:47: BRI0/0:1 DDR: disconnecting call.
> 00:04:49: BRI0/0 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.2)
> 00:04:49: BRI0/0 DDR: Attempting to dial 8895101
> 00:04:49: BRI0/0: wait for isdn carrier timeout, call id=0x8002
> 00:04:49: BRI0/0:1 DDR: disconnecting call.
> 00:04:51: BRI0/0 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.2)
> 00:04:51: BRI0/0 DDR: Attempting to dial 8895101
> 00:04:51: BRI0/0: wait for isdn carrier timeout, call id=0x8003
> 00:04:51: BRI0/0:1 DDR: disconnecting call.
> 00:04:53: BRI0/0 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.2)
> 00:04:53: BRI0/0 DDR: Attempting to dial 8895101
> 00:04:53: BRI0/0: wait for isdn carrier timeout, call id=0x8004
> 00:04:53: BRI0/0:1 DDR: disconnecting call.
> 00:04:55: BRI0/0 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.2)
> 00:04:55: BRI0/0 DDR: Attempting to dial 8895101
> 00:04:55: BRI0/0: wait for isdn carrier timeout, call id=0x8005
> 00:04:55: BRI0/0:1 DDR: disconnecting call.
> Success rate is 0 percent (0/5)
> r5#
> !
>
>
>
>
> ----- Original Message -----
> From: "McCallum, Robert" <Robert.McCallum@let-it-be-thus.com>
> To: "'sanjay'" <ccienxtyear@hotmail.com>; <ccielab@groupstudy.com>
> Sent: Thursday, June 07, 2001 1:47 PM
> Subject: RE: ISDN Troubles
>
>
> > What is the config of your opposite router? Also what is your username
> > password combination for you ppp chap authentication. R they using the
> same
> > password??
> >
> > -----Original Message-----
> > From: sanjay [mailto:ccienxtyear@hotmail.com]
> > Sent: 07 June 2001 21:35
> > To: ccielab@groupstudy.com
> > Subject: ISDN Troubles
> >
> >
> > Hi,
> >
> > I have 2 routers accross an ATLAS 800 ISDN SIM and when I try to ping
from
> > one
> > to another, it doesn't ping. Below is the output of debug dialer and it
> > seems
> > that the problem is with the carrier timeout. Has anyone seen this
before
> > and
> > perhaps recommend on what may be going on. I have also included the
output
> > of
> > show isdn stat and everything there seems to be o.k. Any suggestion is
> > appreciated and thanks in advance.
> >
> >
> >
> >
> > r3#ping 192.168.1.1
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
> >
> > 19:10:29: BRI0/0 DDR: Dialing cause ip (s=192.168.1.2, d=192.168.1.1)
> > 19:10:29: BRI0/0 DDR: Attempting to dial 8895201
> > 19:10:29: BRI0/0: wait for isdn carrier timeout, call id=0x803D
> > 19:10:29: BRI0/0:1 DDR: disconnecting call.
> > 19:10:31: BRI0/0 DDR: Dialing cause ip (s=192.168.1.2, d=192.168.1.1)
> > 19:10:31: BRI0/0 DDR: Attempting to dial 8895201
> > 19:10:31: BRI0/0: wait for isdn carrier timeout, call id=0x803E
> > 19:10:31: BRI0/0:1 DDR: disconnecting call.
> > 19:10:33: BRI0/0 DDR: Dialing cause ip (s=192.168.1.2, d=192.168.1.1)
> > 19:10:33: BRI0/0 DDR: Attempting to dial 8895201
> > 19:10:33: BRI0/0: wait for isdn carrier timeout, call id=0x803F
> > 19:10:33: BRI0/0:1 DDR: disconnecting call.
> > 19:10:35: BRI0/0 DDR: Dialing cause ip (s=192.168.1.2, d=192.168.1.1)
> > 19:10:35: BRI0/0 DDR: Attempting to dial 8895201
> > 19:10:35: BRI0/0: wait for isdn carrier timeout, call id=0x8040
> > 19:10:35: BRI0/0:1 DDR: disconnecting call.
> > 19:10:37: BRI0/0 DDR: Dialing cause ip (s=192.168.1.2, d=192.168.1.1)
> > 19:10:37: BRI0/0 DDR: Attempting to dial 8895201
> > 19:10:37: BRI0/0: wait for isdn carrier timeout, call id=0x8041
> > 19:10:37: BRI0/0:1 DDR: disconnecting call.
> > Success rate is 0 percent (0/5)
> > r3#
> >
> >
> > r3#sh isdn stat
> > Global ISDN Switchtype = basic-ni
> > ISDN BRI0/0 interface
> > dsl 0, interface ISDN Switchtype = basic-ni
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 65, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > Spid Status:
> > TEI 64, ces = 1, state = 8(established)
> > spid1 configured, spid1 sent, spid1 valid
> > Endpoint ID Info: epsf = 0, usid = 70, tid = 1
> > TEI 65, ces = 2, state = 8(established)
> > spid2 configured, spid2 sent, spid2 valid
> > Endpoint ID Info: epsf = 0, usid = 70, tid = 2
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Activated dsl 0 CCBs = 0
> > The Free Channel Mask: 0x80000003
> > Total Allocated ISDN CCBs = 0
> > r3#
> >
> > !
> > interface BRI0/0
> > ip address 192.168.1.2 255.255.255.0
> > no ip directed-broadcast
> > encapsulation ppp
> > dialer idle-timeout 90
> > dialer map ip 192.168.1.1 name r5 broadcast 8895201
> > dialer load-threshold 1 outbound
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 5101 8895101
> > isdn spid2 5102 8895102
> > ppp authentication chap
> > ppp multilink
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:20 GMT-3