From: Jonghwan Hyon (jerry@xxxxxxxxxxxxxxxxxxx)
Date: Fri Jun 01 2001 - 12:13:31 GMT-3
It was a ISDN switch problem!
When isdn circuit was disconnecting, isdn switch can not clear the circuit!
the message is
:
00:56:43: ISDN BR0 U12_DiscReq(), Disconnect collision
00:56:43: ISDN BR0: TX -> SETUP pd = 8 callref = 0x3F
00:56:43: Bearer Capability i = 0x8890
00:56:43: Channel ID i = 0x83
00:56:43: Keypad Facility i = '4821854'
00:56:43: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0xBF
00:56:43: Channel ID i = 0x89
00:56:43: ISDN BR0: RX <- ALERTING pd = 8 callref = 0xBF
00:56:43: Display i = 'Ringing', 0x2020202020202020202020200A, 'please'
, 0x20, 'wait', 0x20., 'a', 0x20, 'minute'
00:56:43: ISDN BR0: Ux_BadMsg(): Invalid Message for call state 4, call id 0x80
40, call ref 0x3F, event 0x85
00:56:43: ISDN BR0: RX <- CONNECT pd = 8 callref = 0xBF
00:56:43: Display i = 'Connected', 0x20202020202020202020200A, 'convers
ation', 0x20, 'now', 0x202020
00:56:43: ISDN BR0: TX -> CONNECT_ACK pd = 8 callref = 0x3F
00:56:43: ISDN BR0: Ux_BadMsg(): Invalid Message for call state 4, call id 0x80
40, call ref 0x3F, event 0x85..
00:56:49: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0xBF
00:56:49: Cause i = 0x80A9 - Temporary failure
00:56:49: Display i = 'Call', 0x20, 'Failure.', 0x20202020202020
00:56:49: Signal i = 0x08 - Off-hook warning tone on
00:56:49: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0xBE
00:56:49: Cause i = 0x80A9 - Temporary failure
00:56:49: Display i = 'Call', 0x20, 'Failure.', 0x20202020202020
00:56:49: Signal i = 0x08 - Off-hook warning tone on
00:56:49: ISDN BR0: TX -> SETUP pd = 8 callref = 0x40
00:56:49: Bearer Capability i = 0x8890
00:56:49: Channel ID i = 0x83
00:56:49: Keypad Facility i = '4821854'
00:56:49: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 70 changed to down
00:56:49: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 70 changed to up
00:56:49: ISDN BR0: TX -> INFORMATION pd = 8 callref = (null)
SPID Information i = '4889476'
00:56:49: ISDN BR0: RX <- CONNECT pd = 8 callref =. 0xC0
00:56:49: Display i = 'Connected', 0x20202020202020202020200A, 'convers
ation', 0x20, 'now', 0x202020
00:56:49: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0x40
00:56:49: Cause i = 0x80D1 - Invalid call reference value
00:56:49: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 70 changed to down
00:56:49: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 70 changed to up.
Success rate is 0 percent (0/5)
----- Original Message -----
From: "John Mistichelli" <jmistichelli@yahoo.com>
To: "Jonghwan Hyon" <jerry@datacraft-korea.com>
Sent: Friday, June 01, 2001 9:55 PM
Subject: Re: Basic isdn problem!
> can you provide a show isdn stat?
>
> It looks like your spids are wrong.
>
> ----- Original Message -----
> From: "Jonghwan Hyon" <jerry@datacraft-korea.com>
> To: "ccie" <ccielab@groupstudy.com>
> Sent: Friday, June 01, 2001 5:15 AM
> Subject: Basic isdn problem!
>
>
> > Hi, i'm trying to enable isdn connection, but they do not work.
> > I have no idea to fix it. can anybody help me?
> >
> >
> > Rack03R5#deb ip packet
> > IP packet debugging is on
> > Rack03R5#ping 132.3.42.3
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 132.3.42.3, timeout is 2 seconds:
> >
> > 00:47:46: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:46: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed
> > 00:47:46: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up.
> > 00:47:46: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 4821854
> > 00:47:48: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:48: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:47:50: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:50: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:47:52: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:52: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:47:52: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 4821854
> > 00:47:54: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:54: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > Success rate is 0 percent (0/5)
> > Rack03R5#ping 132.3.42.3
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 132.3.42.3, timeout is 2 seconds:
> >
> > 00:47:59: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:47:59: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:48:01: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:48:01: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:48:03: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:48:03: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:48:05: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:48:05: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed.
> > 00:48:07: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100, sending
> > 00:48:07: IP: s=132.3.42.5 (local), d=132.3.42.3 (BRI0), len 100,
> encapsulation failed
> > 00:48:08: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 4821854
> , call lasted 22 seconds
> > 00:48:09: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down.
> > Success rate is 0 percent (0/5)
> > Rack03R5#
> > 00:48:09: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 71 changed to
> down
> > 00:48:09: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 71 changed to
> up
> > Rack03R5#
> > Rack03R5#
> > Rack03R5#sh conf
> > Using 1549 out of 32762 bytes
> > !
> > version 12.0
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname Rack03R5
> > !
> > enable password cisco
> > !
> > username Rack03R3 password 0 cisco
> > ip subnet-zero
> > no ip domain-lookup
> > isdn switch-type basic-ni
> > !
> > !
> > !
> > interface Loopback0
> > ip address 132.3.5.5 255.255.255.0
> > no ip directed-broadcast
> > !
> > interface Loopback1
> > ip address 192.192.1.5 255.255.255.0
> > no ip directed-broadcast
> > !
> > interface Ethernet0
> > ip address 10.118.12.1 255.255.255.0
> > no ip directed-broadcast
> > !
> > interface BRI0
> > ip address 132.3.42.5 255.255.255.0
> > no ip directed-broadcast
> > encapsulation ppp
> > no ip route-cache
> > no ip mroute-cache
> > dialer idle-timeout 60
> > dialer map ip 132.3.42.3 name Rack03R3 broadcast 4821854
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 4889476
> > !
> > ip classless
> > ip route 0.0.0.0 0.0.0.0 132.3.42.3 240
> > !
> > dialer-list 1 protocol ip permit
> > !
> > line con 0
> > exec-timeout 0 0
> > password cisco
> > transport input none
> > line aux 0
> > exec-timeout 0 0
> > password cisco
> > line vty 0 4
> > exec-timeout 0 0
> > password cisco
> > login
> > !
> > end
> >
> > Rack03R5#
> >
> > Rack03R3#sh conf
> > Using 1651 out of 32762 bytes
> > !
> > version 12.0
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname Rack03R3
> > !
> > enable password cisco
> > !
> > username Rack03R5 password 0 cisco
> > ip subnet-zero
> > no ip domain-lookup
> > isdn switch-type basic-ni
> > !
> > !
> > !
> > interface Loopback0
> > ip address 132.3.3.3 255.255.255.0
> > no ip directed-broadcast
> > !
> > interface Ethernet0
> > ip address 132.3.41.3 255.255.255.0
> > no ip redirects
> > no ip directed-broadcast
> > !
> > interface BRI0
> > ip address 132.3.42.3 255.255.255.0
> > no ip directed-broadcast
> > encapsulation ppp
> > no ip route-cache
> > no ip mroute-cache
> > dialer idle-timeout 60
> > dialer map ip 132.3.42.5 name Rack03R5 broadcast 4889476
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 4821854
> > !
> > ip classless
> > ip route 132.3.5.0 255.255.255.0 132.3.42.5 240
> > !
> > dialer-list 1 protocol ip permit
> > !
> > line con 0
> > exec-timeout 0 0
> > password cisco
> > transport input none
> > line aux 0
> > exec-timeout 0 0
> > password cisco
> > line vty 0 4
> > exec-timeout 0 0
> > password cisco
> > logging synchronous
> > login
> > !
> > end
> >
> > Rack03R3#
> > ***********************************************
> > Jonghwan Hyon(Jerry), CCNP/CCDP
> > Technical Service/Taejon Branch Office
> >
> > Datacraft Korea, Inc.
> > 320-150, Room #309 Expotel Bldg
> > 381 Man-nyun-dong, Seo-Gu, Taejon, Korea
> >
> > Tel : 8242-487-4272
> > Fax : 8242-487-4273
> > Mobile : 8211-437-8883
> > e-mail : jerry@datacraft-korea.com
> > ***********************************************
> > **Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:16 GMT-3