From: cao lingwei (caolw@xxxxxxxxxxxx)
Date: Mon May 21 2001 - 22:47:15 GMT-3
redistribute connected is wrong,because it will change the ospf database.....
----- Original Message -----
From: "Sandro Ciffali" <sandyccie@yahoo.com>
To: <ccielab@groupstudy.com>
Sent: Tuesday, May 22, 2001 9:05 AM
Subject: Re: another redistribution question
> Here are my two cents on the topic classless to
> classful redistribution.
> I am assuming the ASBR running ospf and igrp has same
> major network and subnets /24 for igrp and /28 for
> ospf, Ospf backbone is area 0 with a multipoint
> network to the other two and point to point to router
> running igrp
> So when you configure IGRP on this ASBR, the OSPF
> interface (/28) is also running igrp in passive mode.
> Now on this router when you say summary address
> x.x.x.x mask It assumes you are summarizing IGRP
> routes being redistributed into OSPF, The summary
> addresses works fine this way, If you check routing
> tables of the other ospf spokes you would see this
> summary route as E2 route (they would have /28 as
> attached and /24 as E2 summary). Then OSPF
> redistributes this route back in IGRP fine. This is
> kind of confusing, Since summary address is generated
> from redistributed route from igrp and then this
> summary address is redistributed back in igrp, but it
> works fine. This works only for ASBR for no other ospf
> router. Atleast i don't know any simpler way than
> this. For router other than asbr the best way is to
> redistribute connected or someway of brining these
> routes external and summarize them.
>
> Thanks
> Sandro
> ----- Original Message -----
> From: "garry baker" <fallow46@yahoo.com>
> To: "David Anderson" <dma@cisco.com>; "Roman Rodichev"
> <rodic000@hotmail.com>
> Cc: <ccielab@groupstudy.com>
> Sent: Sunday, May 20, 2001 11:31 PM
> Subject: RE: another redistribution question
>
>
> > David,
> >
> > you could try a second ospf process and redistribute
> > your main process into your second and then use the
> > summary-address command and redistribute the second
> > process into igrp. i did something like this
> recently
> > but i had to redistribute both ospf processes to get
> > all my /24 routes into igrp, not too sure why i had
> to
> > do that, does anyone have any ideas?
> >
> > Garry
> > --- David Anderson <dma@cisco.com> wrote:
> > > Roman,
> > > I tried the area 0 range on one of the routers
> that
> > > was one hop away from
> > > the ASBR. However the ASBR is also part of area 0
> > > and I cant seem to get
> > > the summary route to show up in the ASBR or any of
> > > the routers. Any
> > > ideas? I am going to try again and just see if I
> > > missed something.
> > > Thanks,
> > > David
> > > At 09:45 PM 5/20/2001 -0500, Roman Rodichev wrote:
> > >
> > > >Where did you see that command?! I don't think it
> > > exists. :) Summarization
> > > >doesn't make any sense under IGRP. It is
> classful.
> > > >
> > > >ip summary-address can only be done for EIGRP and
> > > RIPv2
> > > >
> > > >roman
> > > >
> > > >
> > > >>From: "Gregory W. Posey Jr."
> <gposey@conects.com>
> > > >>Reply-To: "Gregory W. Posey Jr."
> > > <gposey@conects.com>
> > > >>To: "David Anderson" <dma@cisco.com>,
> > > <ccielab@groupstudy.com>
> > > >>Subject: RE: another redistribution question
> > > >>Date: Sun, 20 May 2001 22:17:39 -0400
> > > >>
> > > >>I believe you use the "summary-address" command
> > > when summarizing between
> > > >>OSPF and another routing protocol.
> > > >>
> > > >>The "area range" command is for when you
> summarize
> > > from one area to the next
> > > >>(on an ABR) within OSPF.
> > > >>
> > > >>To summarize from one protocol (e.g. EIGRP) into
> > > OSPF, use the
> > > >>"summary-address" command under the OSPF
> > > "config-router" mode.
> > > >>
> > > >>For your situation (summarizing from OSPF into
> > > another routing protocol), if
> > > >>IGRP acts the same as EIGRP, then you configure
> it
> > > under the interface
> > > >>"config-if" mode, and the command is...
> > > >>
> > > >>"ip summary-address igrp 101 X.X.X.X Y.Y.Y.Y"
> > > >>
> > > >>Of course either/both command(s) is/are
> configured
> > > on the router that runs
> > > >>both OSPF and IGRP.
> > > >>
> > > >>
> > > >>Thank you,
> > > >>Greg Posey Jr.
> > > >>CONECTS Network Analyst
> > > >>CCNP - Security Specialist
> > > >>Cisco Voice Access Specialist
> > > >>
> > > >>-----Original Message-----
> > > >>From: nobody@groupstudy.com
> > > [mailto:nobody@groupstudy.com]On Behalf Of
> > > >>David Anderson
> > > >>Sent: Sunday, May 20, 2001 9:24 PM
> > > >>To: ccielab@groupstudy.com
> > > >>Subject: another redistribution question
> > > >>
> > > >>
> > > >>Ok, here is my redistribution question:
> > > >>
> > > >>Suppose I have an OSPF area (say area 0) with a
> > > /28 mask and I am
> > > >>redistributing with IGRP which has a /24 mask.
> > > Can one summarize the area
> > > >>0 using the area range command on the ASBR? I
> > > tried and could not get it
> > > >>to work. However, what I did get to work was to
> > > create a loopback on
> > > >>another router in my ospf domain using the same
> > > subnet I have in my area 0,
> > > >>but with a /24 mask and then advertised that
> into
> > > ospf and all was well on
> > > >>the IGRP router. I could ping all of my /28
> ospf
> > > interfaces. Does anyone
> > > >>have any suggestions other than this? Did I
> miss
> > > anything?
> > > >>
> > > >>Thanks everyone,
> > > >>David
> > > >>David Anderson
> > > >>Network Design Engineer
> > > >>Enterprise Solutions Architecture & Design
> > > >>(408) 853-5515
> > > >>dma@cisco.com
> > > >> | |
> > > >> ..:|||||||:...:|||||||:..
> > > >>C I S C O S Y S T E M S
> > > >>**Please
> > > read:http://www.groupstudy.com/list/posting.html
> > > >>**Please
> > > read:http://www.groupstudy.com/list/posting.html
> > >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:48 GMT-3