From: emonk@xxxxxxx
Date: Mon May 21 2001 - 13:58:11 GMT-3
Guys,
The only command required under the lines is.
"Transport input all". Here is my output from my 2511
with comments at each type of line. I have also owned a
2509 and it was exactly the same except I only had line
1-8. Guaranteed this is correct.
Needed for your PC console session.
line con 0
exec-timeout 0 0 <-- Optional. The exec-timeout 0 0
keeps your session from timing out.
privilege level 15 <-- Optional. Puts you into
executive privilege mode without having to go through
the motions.
**These are your lines that go to your test Routers with
the octopus cable. Yours on a 2509 will be "line 1 8".
line 1 16
transport input all
**No config needed here. Usually used for asynch backup
device. Like a modem. Probably should play with it.
line aux 0
**No config. needed here. Just for telnetting to
termserver. Should set it up and play with it. I
included my config statements so you had an example.
line vty 0 4
privilege level 15
password xxxxx
login
transport input telnet
> Is it necessary to also add the command "no exec", that prevents the output
> of the routers you are reverse telnetting into from initiating a session
> with the terminal server? I had problems with my terminal server until I
> added this command.
>
> Bruce
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Chris Mott
> Sent: Sunday, May 20, 2001 11:53 AM
> To: CCIE; Jeongwoo Park
> Subject: RE: Terminal Server for the first time !!! [7:5119]
>
>
> Use these two commands alone on the "line vty 0 ?" section:
>
> no exec-timeout
> transport input all
>
> remove the rest, and continue working normally ... and don't confuse issues
> by adding too many commands! this will bite you in the lab ... do only what
> is required, with a minimal set of commands, and move on ... getting cute or
> tricky is not the goal of the lab ... most often, the more complicated
> questions have as an answer one or two commands, nothing more ...
>
> HTH
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Jeongwoo Park
> Sent: Sunday, May 20, 2001 4:40 AM
> To: Yongchul Yang; Ccielab@Groupstudy. Com
> Subject: RE: Terminal Server for the first time !!! [7:5119]
>
>
> Hi all
> I made some changes on config.
> Still didn't work.
>
> Here is new config:
>
>
> TermServer#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname TermServer
> !
> enable password wams
> !
> ip subnet-zero
> no ip domain-lookup
> ip host r1 2001 1.1.1.1
> ip host r2 2002 1.1.1.1
> ip host r3 2003 1.1.1.1
> !
> !
> !
> interface Loopback0
> ip address 1.1.1.1 255.255.255.255
> no ip directed-broadcast
> !
> interface Ethernet0
> no ip address
> no ip directed-broadcast
> shutdown
> !
> interface Serial0
> ip address 5.5.5.5 255.255.255.0
> no ip directed-broadcast
> no ip mroute-cache
> no fair-queue
> clockrate 64000
> !
> interface Serial1
> ip address 5.5.6.5 255.255.255.0
> no ip directed-broadcast
> !
> ip classless
> !
> !
> line con 0
> no exec
> transport input none
> line 1 8
> transport input all
> transport output none
> stopbits 1
> line aux 0
> line vty 0 4
> login
> !
> end
>
> Now I did "sh line"
>
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
> * 0 CTY - - - - - 15 0 0/0 -
> * 1 TTY 9600/9600 - - - - - 7 20 4/17 -
> * 2 TTY 9600/9600 - - - - - 7 0 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
> 10 VTY - - - - - 0 0 0/0 -
> 11 VTY - - - - - 0 0 0/0 -
> 12 VTY - - - - - 0 0 0/0 -
> 13 VTY - - - - - 0 0 0/0 -
> 14 VTY - - - - - 0 0 0/0 -
>
> Then I did this
>
> TermServer#clear line 1
> [confirm]
> [OK]
> TermServer#clear line 2
> [confirm]
> [OK]
> TermServer#clear line 8
> [confirm]
> [OK]
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
> * 0 CTY - - - - - 15 0 0/0 -
> 1 TTY 9600/9600 - - - - - 7 90 7/26 -
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
> 10 VTY - - - - - 0 0 0/0 -
> 11 VTY - - - - - 0 0 0/0 -
> 12 VTY - - - - - 0 0 0/0 -
> 13 VTY - - - - - 0 0 0/0 -
> 14 VTY - - - - - 0 0 0/0 -
>
> Now it shows this:
>
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
> * 0 CTY - - - - - 15 0 0/0 -
> 1 TTY 9600/9600 - - - - - 7 90 7/26 -
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
> 10 VTY - - - - - 0 0 0/0 -
> 11 VTY - - - - - 0 0 0/0 -
> 12 VTY - - - - - 0 0 0/0 -
> 13 VTY - - - - - 0 0 0/0 -
> 14 VTY - - - - - 0 0 0/0 -
>
> At this point, I am confused because line 8 was not cleared.
>
> Now I typed "r1" This is what it looks like:
>
> TermServer#r1
> Trying r1 (1.1.1.1, 2001)... Open
> And I get stuck forever.
> I had to go (ctrl+shift+6)+X to go back to TermServer prompt.
> At TermServer prompt, I did "sh line" again.
>
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
> * 0 CTY - - - - - 16 0 0/0 -
> * 1 TTY 9600/9600 - - - - - 8 90 7/26 -
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
> 10 VTY - - - - - 0 0 0/0 -
> 11 VTY - - - - - 0 0 0/0 -
> 12 VTY - - - - - 0 0 0/0 -
> 13 VTY - - - - - 0 0 0/0 -
> 14 VTY - - - - - 0 0 0/0 -
>
> So I cleared line 1 by doing this "clear line 1"
> And typed r1. It still showed this shit.
> TermServer#r1
> Trying r1 (1.1.1.1, 2001)... Open
>
> I just made longer message than I intended to. But since I am struggling to
> get this to work, I want to try every possible way.
> I hope I showed you better.
> Any input would be appreciated
> Thanks.
>
> Jeongwoo
>
>
>
> -----Original Message-----
> From: Yongchul Yang [mailto:whycwhy@socal.rr.com]
> Sent: Sunday, May 20, 2001 12:09 AM
> To: Jeongwoo Park
> Subject: RE: Terminal Server for the first time !!! [7:5119]
>
>
> Jeongwoo,
>
> Don't let other sample configuration confuse you, your configuration is
> absolutely correct. It just takes a few practice sessions to get
> comfortable using the terminal server. A lot of people make simple mistakes
> on how to use it. Just simply press 2nd 'enter' key after typing r1 &
> enter. If the session is refused by any reason, just check the line status
> with either 'show session' or 'show line' command. If you are using 2509
> with rj45 asynch interface make sure you are using the rolled cable, if you
> are using the octal cable, they are already rolled. Another scenario is
> using the rj45 patch panel, if you have octal or rolled rj45 cable connected
> to the patch panel, make sure you are using the straight cable between your
> routers' console ports.
>
> Once you have the physical set up of using the terminal server, keep
> practice using it on all you lab exam practice, then you will start
> developing some short cuts of your own. I don't particularly like using the
> terminal server because I can only monitor one router at a time, but that's
> what you are going to have at your lab exam.
>
> Good luck,
>
> Yongchul Yang
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Jeongwoo Park
> Sent: Saturday, May 19, 2001 7:34 AM
> To: cisco@groupstudy.com
> Subject: Terminal Server for the first time !!! [7:5119]
>
> Hi all
> How can I get my 2509 terminal server to work?
> Here is my config
>
> TermServer#sh r
> 05:47:29: %SYS-5-CONFIG_I: Configured from console by consoleun
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname TermServer
> !
> enable password wams
> !
> ip subnet-zero
> no ip domain-lookup
> ip host r1 2001 1.1.1.1
> ip host r2 2002 1.1.1.1
> ip host r3 2003 1.1.1.1
> !
> !
> !
> interface Loopback0
> ip address 1.1.1.1 255.255.255.255
> no ip directed-broadcast
> !
> interface Ethernet0
> no ip address
> no ip directed-broadcast
> shutdown
> !
> interface Serial0
> ip address 2.2.50.2 255.255.255.252
> no ip directed-broadcast
> no ip mroute-cache
> no fair-queue
> clockrate 64000
> shutdown
>
> !
> interface Serial1
> ip address 3.3.50.1 255.255.255.252
> no ip directed-broadcast
> clockrate 1300000
> shutdown
> !
> ip classless
> !
> !
> line con 0
> line 1 8
> no exec
> transport input all
> line aux 0
> line vty 0 4
> login
> !
> end
>
> I have three other router that are r1, r2, and r3 respectively.
> How can I get to r1, r2, or r3?
> Isn't it this one? for example,
> TermServer#r1
> TermServer#r2
> TermServer#r3
> It did not work
> I am using termserver for the first time.
> Can someone guide me through how to use it?
>
> In addition, here is output of "sh line"
>
> TermServer#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
> * 0 CTY - - - - - 6 1 0/0 -
> * 1 TTY 9600/9600 - - - - - 3 2 0/0 -
> * 2 TTY 9600/9600 - - - - - 2 0 0/0 -
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
> 5 TTY 9600/9600 - - - - - 0 104 0/0 -
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
> 7 TTY 9600/9600 - - - - - 1 0 81/243 -
> 8 TTY 9600/9600 - - - - - 0 6 208/622 -
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
> 10 VTY - - - - - 1 0 0/0 -
> 11 VTY - - - - - 0 0 0/0 -
> 12 VTY - - - - - 0 0 0/0 -
> 13 VTY - - - - - 0 0 0/0 -
> 14 VTY - - - - - 0 0 0/0 -
> Thanks
>
> jp
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to abuse@groupstudy.com
> **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:47 GMT-3