From: Connary, Julie Ann (jconnary@xxxxxxxxx)
Date: Fri May 04 2001 - 16:51:47 GMT-3
See the archives - I posted this a while ago - use snasw and a router
running 12.1 code.
Julie Ann
At 01:38 AM 4/20/2001 +0300, Elias Aggelidis wrote:
>Dear Glen
>
>I am trying to implement what you have proposed
>But no lack !!!!!
>
>DSPU HOST TESTDLSW is trying again and again but the other end
>does not send a bit.
>
>Any hinds ?
>
>Regards
>
>****************************************************************
>Elias Aggelidis ALGOSYSTEMS SA
>Senior Network Engineer 4, Sardeon Str
>CCNA, CCNP Nea Smyrni
>CVOICE, Security Specialised
>PICA Administrator
> Athens 17121
>tel: +301-9310281 GREECE
>fax: +301-9352873
>email: eaggel@algo.com.gr
>****************************************************************
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Glen
>Lavers
>Sent: ??5pt?, 19 ?p?????? 2001 12:30 55
>To: Devender Singh; Ccielab@Groupstudy. Com (E-mail)
>Subject: RE: DLSW: How do generate DLSW traffic from routers.
>
>
>I think this is what you might be after.
>Glen
>
><<---
>R1(HOST)--t/r--R2--DLSw--R3--t/r--R4(PU)
>
>In the above topology R2 and R3 are dlsw peers.
>R4 is trying to connect to R1 using LLC2 as
>as its transport for SNA..
>
>You can replace the tokenrings with ethernets,
>and leave the below config untouched
>
>If you change only one side do not forget the bitswapping :
>http://www-tac.cisco.com/TOOLS/Applications/bitswap.html
>
>
>Sending Router (emulating SNA PU) -> R4
>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>dspu host TESTDLSW xid-snd 01712345 rmac 4000.3745.0001 rsap 4 lsap 4
>
>interface TokenRing0
>dspu enable-host lsap 4
>dspu start TESTDLSW
>end
>
>Receiving Router (emulating Mainframe) -> R1
>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>dspu pu HOST xid-rcv 01712345
>
>interface TokenRing0
>mac-address 4000.3745.0001
>dspu enable-pu lsap 4
>
>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
>Commands to use :
>
>show dlsw peer
>show dlsw reach
>show dlsw circuit detail
>show llc
>show rif
>show source
>debug dlsw core
>debug token ring
>
>
>
>*****************************************************************
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
>Devender Singh
>Sent: Wednesday, April 18, 2001 10:34 AM
>To: Ccielab@Groupstudy. Com (E-mail)
>Subject: DLSW: How do generate DLSW traffic from routers.
>
>
>Can someone guide me how to generate DLSW traffic, so that can do some real
>work on dlsw.
>
>thanks in advance.
>
>Devender Singh
>BE(Hons), CCNP
>IP Solution Specialist
>**Please read:http://www.groupstudy.com/list/posting.html
>**Please read:http://www.groupstudy.com/list/posting.html
>**Please read:http://www.groupstudy.com/list/posting.html
------------------------------------------------------------------------
Julie Ann Connary
| | Network Consulting Engineer
||| ||| Federal Support Program
.|||||. .|||||. 13635 Dulles Technology Drive,
Herndon VA 20171
.:|||||||||:.:|||||||||:. Pager: 1-888-642-0551
c i s c o S y s t e m s Email: jconnary@cisco.com
------------------------------------------------------------------------
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:34 GMT-3