From: Chris Mott (cmott@xxxxxxxx)
Date: Mon Apr 30 2001 - 14:53:07 GMT-3
Be aware that if your emulation is DMS-100 you will need to change the
SPID's to terminate with "00" or "01" ... I have a Black Box ISDN simulator
set as DMS-100 and my SPID's work ok ... please issue a deb for : q921,
q931, dialer ... then post and we'll take a further look
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Moran, Ed
Sent: Sunday, April 29, 2001 12:25 PM
To: 'ccielab@groupstudy.com '
Subject: RE: ISDN Connection Problem
I made the ISDN connection one-way so that R4 dials R3 and R3 does not
initiate a connection. The problem is still around. I still don't know what
the problem is. Thanks for all the help to all of you.
-----Original Message-----
From: Michael Davis
To: Moran, Ed; ccielab@groupstudy.com
Sent: 4/28/01 4:35 PM
Subject: Re: ISDN Connection Problem
Can you post a sh isdn stat and a debug isdn q921? They may help.
----- Original Message -----
From: "Moran, Ed" <morane@telecomsys.com>
To: <ccielab@groupstudy.com>
Sent: Saturday, April 28, 2001 3:45 PM
Subject: RE: ISDN Connection Problem
> I have reset the switch and changed the switch type to Basic-DMS100 as
> well. I also change it on the routers and sim. The error is still the
same.
> I know the sim works as I have used it many times in the past. Any
help?
>
> -----Original Message-----
> From: Moran, Ed
> To: 'ccielab@groupstudy.com'
> Sent: 4/28/01 3:26 PM
> Subject: RE: ISDN Connection Problem
>
> The SPIDS are valid and there is no problem there. I will try
rebotting
> the
> simulator (BlackBox) and see what happens.
>
> -----Original Message-----
> From: Michael Herald
> To: 'Moran, Ed'
> Sent: 4/28/01 2:57 PM
> Subject: RE: ISDN Connection Problem
>
> Ed,
>
> The spids have been entered incorrectly. In the debug, it says there
was
> a SPID rejected ....
>
> Do a "show isdn status". You should see (similar to, depending on
> switch):
> r1-2504#show isdn status
> The current ISDN Switchtype = basic-dms100
> ISDN BRI0 interface
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 126, State = MULTIPLE_FRAME_ESTABLISHED
> TEI = 65, State = MULTIPLE_FRAME_ESTABLISHED
> Spid Status:
> TEI 126, ces = 1, state = 5(init)
> spid1 configured, spid1 sent, spid1 valid
> Endpoint ID Info: epsf = 0, usid = 2, tid = 1
> TEI 65, ces = 2, state = 5(init)
> spid2 configured, spid2 sent, spid2 valid
> Endpoint ID Info: epsf = 0, usid = 4, tid = 1
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Activated dsl 0 CCBs = 0
> Total Allocated ISDN CCBs = 0
>
>
>
>
> -----Original Message-----
> From: Moran, Ed [SMTP:morane@telecomsys.com]
> Sent: Saturday, April 28, 2001 12:10 PM
> To: 'ccielab@groupstudy.com'
> Subject: ISDN Connection Problem
>
> I am having problems connecting 2 routers via ISDN. Here is the 'deb
> isdn
> q931' output. Can anyone tell me what the problem is? If needed, I
will
> post
> my configs.
>
> R3#deb isdn q931
> ISDN Q931 packets debugging is on
> R3#ping 139.5.12.14
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 139.5.12.14, timeout is 2 seconds:
>
> 3d15h: ISDN BR0: TX -> SETUP pd = 8 callref = 0x17
> 3d15h: Bearer Capability i = 0x8890
> 3d15h: Channel ID i = 0x83
> 3d15h: Keypad Facility i = '8358662'
> 3d15h: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x97
> 3d15h: Cause i = 0x82A2 - No channel available
> 3d15h: ISDN BR0: Setup was rejected, cause = 22.....
> Success rate is 0 percent (0/5)
> R3#
>
> Ed
> **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:02 GMT-3