From: glange@xxxxxxxxx
Date: Fri Apr 27 2001 - 08:48:37 GMT-3
Hello,
this is the configuration from the site.
But I think, this can't function, because of
"source-bridge transparent 500 1000 1 1"
The used bridge-numbers for transparent and source-route are 5 and 1
and not 1 (-> should be ?: source-bridge transparent 500 1000 5 1)
Or I don't have to care about the (different) bridge-numbers in this
command ?
.
source-bridge ring-group 500
source-bridge transparent 500 1000 1 1
dlsw local-peer peer-id 128.207.1.145
dlsw remote-peer 0 tcp 128.207.111.1 lf 1500
dlsw bridge-group 5
.
.
.
interface ethernet 1/2
ip address 128.207.1.145 255.255.255.0
bridge-group 5
.
.
.
interface tokenring 2/0
no ip address
ring-speed 16
source-bridge 7 1 500
source-bridge spanning
!
.
.
.
bridge 5 protocol ieee
> I'm confused. The config for the router that has the TR and Ethernet
> interfaces DOES have sr/tlb configured. We're looking at the section
titled
> "Figure 106: DLSw+ Translation between Ethernet and Token Ring",
right?
> Router B is the one with both media types on it.
>
> DLSW will do the conversion for stuff going across the link to another
> router. For stuff going from one interface on the router to another
> interface on the same router, DLSW won't kick in, so you HAVE to
configure
> sr/tlb to do it.
>
> Aaryn Pickell - CCNP, CCDP, MCSE
> Senior Engineer - Routing Protocols
> Getronics Inc.
> Direct: 713-394-1609
> Email:aaryn.pickell@getronics.com
>
> This e-mail message and any attachments are confidential and may be
> privileged. If you are not the intended recipient, please notify me
> immediately by replying to this message and please destroy all copies
of
> this message and attachments. Thank you.
>
>
>
> > -----Original Message-----
> > From: Kirk Bollinger [mailto:kirk@thebollingers.net]
> > Sent: Thursday, April 26, 2001 8:40 AM
> > To: ccielab@groupstudy.com
> > Subject: single router dlsw ether+token
> >
> >
> > I found this link on CCO
> >
> > http://www.cisco.com/univercd/cc/td/doc/product/software/ios12
> > 0/12cgcr/ibm_c/bcprt2/bcdlsw.htm#xtocid2338139
> >
> > (watch wrap)
> >
> > It has a config example with dlsw on a single router sith
> > both ethernet
> > and tokenring and it does not includethe config for SR/TLB.
> >
> > So, now we have Caslow saying that SR/TLB is a requirement
> > and this doc
> > without it.
> >
> > any ideas?
> >
> > Obviously SR/TLB will work but it'll bridge non routable
> > protocols between
> > the interfaces and the simple straight dlsw config won't.
> >
> > -lorl
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:59 GMT-3