From: Ladipo Adefala (ladefala@xxxxxxxxxxx)
Date: Thu Apr 19 2001 - 21:27:37 GMT-3
Thanks to all who responded.
>From: Jose Ferreira <jvf@cisco.com>
>To: "Ladipo Adefala" <ladefala@hotmail.com>, lkouncar@UU.NET,
>carlphelan@hotmail.com, ccielab@groupstudy.com
>Subject: RE: Frame Relay Switch with 2 Routers
>Date: Fri, 20 Apr 2001 01:16:18 +0000
>
>I didn't understand completely your question, but here are a couple of
>options:
>
>Back-to-back FR:
>http://www.cisco.com/warp/public/125/frbacktoback.html
>
>Back-to-back FR Hybrid Switching:
>http://www.cisco.com/warp/public/125/frbacktoback_hybrid.html
>
>If on the other hand you're trying to do FR switching over and IP tunnel,
>then I found in the past thar this feature seems to be only available on
>the IOS Enterprise feature set (although it is an old feature and should be
>there in a 12.0).
>For config see:
>http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_c/
wcdfrely.htm#xtocid15531103
>
>Regards,
>Josi
>
>At 00:51 20/04/01 +0100, Ladipo Adefala wrote:
>>I was able to get the appropriate command completion (v 12.07T), but it
>>looks like my end-to-end pvcs remain INACTIVE. A show frame route on both
>>routers acting as a frame switch shows that one-end of the PVCs are active
>>while the other end of the PVCs are INACTIVE.
>>I hope this isn't an issue with the code. Does anyone have any ideas?
>>Ladi
>>
>>>From: "louie kouncar" <lkouncar@UU.NET>
>>>Reply-To: "louie kouncar" <lkouncar@UU.NET>
>>>To: "'Carl Phelan'" <carlphelan@hotmail.com>, <ccielab@groupstudy.com>
>>>Subject: RE: Frame Relay Switch with 2 Routers
>>>Date: Thu, 19 Apr 2001 19:41:26 -0400
>>>
>>>You can't use frame relay on a token ring or Ethernet.
>>>
>>>
>>>Louie J. Kouncar (CCIE)/Written
>>>TCO3 Senior Data Center Engineer
>>>UUNET
>>>W-703-343-6645
>>>C-703-304-2460
>>>
>>>
>>>
>>>-----Original Message-----
>>>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
>>>Carl Phelan
>>>Sent: Thursday, April 19, 2001 6:40 PM
>>>To: ccielab@groupstudy.com
>>>Subject: Frame Relay Switch with 2 Routers
>>>
>>>
>>>Hi,
>>>
>>>I am following the document from CCprep to create a frame relay switch
>>>from
>>>two 2501s. When I come to enter the following command:
>>>'frame-relay route 501 interface t0 105'
>>>in interface mode on Serial 1, the router reports an error in the command
>>>syntax with 't' or even the full word 'tunnel'. When I replace 't0' with
>>>a
>>>?
>>>the response is that it only expects the word 'serial'.
>>>I have tried IOS ver 11.1, 11.2 and 12.0 with the same problem on
>>>different
>>>routers - anybody have any ideas?
>>>
>>>Thanks.
>>>**Please read:http://www.groupstudy.com/list/posting.html
>>>**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:52 GMT-3