From: Williams, Bruce (BWilliams@xxxxxxxxxxxxxxxx)
Date: Tue Apr 10 2001 - 10:37:34 GMT-3
Please forgive my ignorance. What is this ATM Oilcom 8008?
Bruce Williams
mailto:bruce@williamsnetworking.com
-----Original Message-----
From: Tariq Sharif [mailto:tariq_sharif@btinternet.com]
Sent: Tuesday, April 10, 2001 9:32 AM
To: Ccielab@Groupstudy. Com; Randy Feliz
Subject: RE: ATM Olicom 8008 Switch Users pls help!
Randy
It works! the default password WAS "private". Don't know why the manual I
have says otherwise. Thanks a LOT for your help!
Many thanks & regards.
Tariq Sharif
-----Original Message-----
From: Randy Feliz [mailto:rjfeliz@yahoo.com]
Sent: 10 April 2001 17:02
To: Tariq Sharif
Subject: Re: ATM Olicom 8008 Switch Users pls help!
Tariq,
in my manual on page 4-8 it states that the default "write" password is
"private"
Randy Feliz
Senior Network Engineer
CCIE# 4331(R/S, ISP Dial)
----- Original Message -----
From: Tariq Sharif <tariq_sharif@btinternet.com>
To: Randy Feliz <rjfeliz@yahoo.com>
Sent: Tuesday, April 10, 2001 5:49 AM
Subject: RE: ATM Olicom 8008 Switch Users pls help!
> Randy
>
> Trying to go into "Access Mode write" at the command with "prompt> system
> set access write" it asks for password which manuals says default is
> AaBbCcDd.
>
> Many thanks & regards.
>
> Tariq Sharif
>
>
> -----Original Message-----
> From: Randy Feliz [mailto:rjfeliz@yahoo.com]
> Sent: 10 April 2001 16:39
> To: Tariq Sharif
> Subject: Re: ATM Olicom 8008 Switch Users pls help!
>
>
> tariq,
> the default is "private"
> what mode are you trying to get into..and what command are you using
>
> Randy Feliz
> Senior Network Engineer
> CCIE# 4331(R/S, ISP Dial)
> ----- Original Message -----
> From: Tariq Sharif <tariq_sharif@btinternet.com>
> To: Randy Feliz <rjfeliz@yahoo.com>
> Sent: Tuesday, April 10, 2001 4:18 AM
> Subject: RE: ATM Olicom 8008 Switch Users pls help!
>
>
> > Randy
> >
> >
> > I Can't get into ATM Olicom 8008 ATM switch using default console
> password.
> > Do you know
> > how to break into it? Manual says default passwords is AaBbCcDd does not
> > work. There is reset
> > button but that restarts the switch. I've also tried keeping the reset
> > button pressed for 15 seconds while switching on the box but it does not
> > help. Can you help?
> >
> >
> > Many thanks & regards.
> >
> > Tariq Sharif
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Randy Feliz
> > Sent: 21 March 2001 17:27
> > To: Tariq Sharif; Ccielab@Groupstudy. Com
> > Subject: Re: ATM Olicom 8008 Switch Users pls help!
> >
> >
> > Tariq,
> > I just purchased a couple of Olicom switches to use in a lab...from what
I
> > can tell they can come with either the Multimode modules or the Single
> mode
> > module...I think that the command that will show you this is "atm show
> > interface"...(I don't remember the syntax of the command, and I am not
in
> > front of my switch) One of the switches came with SM, the other came
with
> > both MM and SM...I have not had the time to start playing with them yet
> > Randy Feliz
> > Senior Network Engineer
> > CCIE# 4331(R/S, ISP Dial)
> > ----- Original Message -----
> > From: Tariq Sharif <tariq_sharif@btinternet.com>
> > To: Ccielab@Groupstudy. Com <ccielab@groupstudy.com>
> > Sent: Tuesday, March 20, 2001 10:06 AM
> > Subject: ATM Olicom 8008 Switch Users pls help!
> >
> >
> > > Can someone pls help with ATM Olicom CrossFire 8008 with 12 ports (MOD
> > > 8000/2) setup. The issues are:
> > >
> > > 1) Should it be used as multimode or Singlemode? How is this done,
e.g.
> is
> > > it just a function of cables you use, SC or ST?
> > > 2) Looking to get ATM Router modules for Cisco 7000, should I get
> > multimode
> > > (SM) or Singlemode (MM) ones?
> > >
> > > Many thanks & regards.
> > >
> > > Tariq Sharif
> > >
> > >
> > > **NOTE** All LAB SWAP messages should now be sent to the
> > > LAB SWAP Message board on groupstudy.com.
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:43 GMT-3