From: Rick Burts (burts@xxxxxxxxxxxxxx)
Date: Sun Feb 18 2001 - 09:48:33 GMT-3
Gary
no auto-summary is an option for EIGRP. You may use it where you think
appropriate but it is certainly not a requirement.
Rick
Rick Burts, CCSI CCIE 4615 burts@mentortech.com
Mentor Technologies 240-568-6500 ext 6652
133 National Business Parkway 240-568-6515 fax
Annapolis Junction, Md 20701
Chesapeake Network Solutions has now become Mentor Technologies.
Mentor Technologies is a certified Cisco Training Partner and also
a Cisco Professional Services partner.
We offer most of the Cisco training courses.
We also offer training in Checkpoint Firewall software and
Fore Systems (now Marconi) and MicroMuse.
We also provide network consulting services including
design, management, and problem solving.
We have 22 CCIEs on our staff.
We offer the breakthrough VLAB remote access technology for
access to pratice configuration on real equipment.
On Sun, 18 Feb 2001, Gary Marsh wrote:
> Don't you need to use the command no auto-summary with EIGRP.
>
> Regards,
>
> Gary
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Dan
> Sent: Sunday, February 18, 2001 12:16 AM
> To: J. Kata; ccielab@groupstudy.com
> Subject: Re: EIGRP Wildcard mask? Yes, yes I should know this...but I'm an
> OSPF man
>
> Ok so to further expand on that, let's say I have the config below:
>
> interface Ethernet0/0
> ip address 192.168.1.17 255.255.255.248
>
> inteface Ethernet0/1
> ip address 192.168.1.33 255.255.255.248
>
> If I only want to advertise Ethernet0/0 via EIGRP, but not Ethernet0/1.
>
> I must filter within the EIGRP process to stop 192.168.1.32 /29 from being
> advertised?
>
> EIGRP 1
> network 192.168.1.0
> distribute-list 1 in
>
>
> access-list 1 permit 192.168.1.16
>
> Is this correct? Wildcard masks are much easier.
>
> Dan Pontrelli
> Customer Installation Engineer - Verio NYC
> CCNP, MCSE, CNA
>
>
> ----- Original Message -----
> From: "J. Kata" <jkata@mindspring.com>
> To: <ccielab@groupstudy.com>
> Sent: Saturday, February 17, 2001 6:08 PM
> Subject: RE: EIGRP Wildcard mask? Yes, yes I should know this...but I'm an
> OSPF man
>
>
> > Only IOS versions 12.0(4)T and up support wildcard statements.
> >
> > -- Janusz Kata
> >
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > > Dan
> > > Sent: Saturday, February 17, 2001 5:06 PM
> > > To: ccielab@groupstudy.com
> > > Subject: EIGRP Wildcard mask? Yes, yes I should know this...but I'm an
> > > OSPF man
> > >
> > >
> > > I have noticed that in most cases EIGRP will not let me enter a wild =
> > > card mask after the network "x.x.x.x" statement.
> > > But I remember in the past that I have been able to do this. I'm a bit
> =
> > > confused by this.
> > > EIGRP is supposed to be a classless protocol, but after entering all my
> =
> > > subnets under the EIGRP process, I see that it's summarizing them at the
> =
> > > classful boundary, even though I have disabled automatic summarization.
> =
> > >
> > > Why does this happen and am I correct that it sometimes let's you add a
> =
> > > wildcard mask like OSPF does?
> > >
> > >
> > > Dan Pontrelli
> > > Customer Installation Engineer - Verio NYC
> > > CCNP, MCSE, CNA
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:28:52 GMT-3