From: Elias Aggelidis (eaggel@xxxxxxxxxxx)
Date: Sun Feb 11 2001 - 13:31:43 GMT-3
Added to that if you have an PC attached to the ethernet of router (eg 2)
you have to put the ip policy route-map xxx command on that interface two
if you want every Workstation on that interface to speak with all the
others.
Policy routing is something we are going to find a lot on the lab.
Keep up practicing .
Regards
Elias Aggelidis
----- Original Message -----
From: "Steven Weber" <itweber@netzero.net>
To: "Mark Stover" <mstover@cisco.com>; <ccielab@groupstudy.com>
Sent: Sunday, February 11, 2001 6:54 AM
Subject: Re: ccbootcamp lab#1...
> Thanks Mark, my etherenet was up down I forgot to shut off keepalives and
I had
> the addressing on the virtual link reversed. The answers show that there
is an
> access-list for all of the routes in the entire network that are used in
the
> route-map, but I was able to do it with only putting the spokes into the
> access-list.
> Thanks for the help
> Steve
>
> Mark Stover wrote:
>
> > Do a show ip ospf interface on each router and make sure that they have
OSPF
> > configured on them.
> > Mark
> >
> > -----Original Message-----
> > From: Steven Weber [mailto:itweber@netzero.net]
> > Sent: Saturday, February 10, 2001 10:59 PM
> > To: Mark Stover
> > Subject: Re: ccbootcamp lab#1...
> >
> > For some reason the e0 in r2 and the lo0 and l01 on r4 aren't showing
up
> > anywhere else in the network butn the e0's on r5 and r1 are. Any
> > suggestions.
> > Steve
> >
> > Mark Stover wrote:
> >
> > > It's used to enable the application of policy routing to traffic that
> > > originates from the router. Policy routing normally only applies to
> > traffic
> > > that transits the router.
> > >
> > > Mark
> > >
> > > -----Original Message-----
> > > From: Steven Weber [mailto:itweber@netzero.net]
> > > Sent: Saturday, February 10, 2001 10:15 PM
> > > To: Mark Stover
> > > Cc: bruce@williamsnetworking.com; ccielab@groupstudy.com
> > > Subject: Re: ccbootcamp lab#1...
> > >
> > > Thanks Mark,
> > > I reviewed the answers and noticed that I left out the ip local policy
> > > route-map
> > > FRAM in my config. I've never come accross this before what is this
> > command
> > > used
> > > for?
> > > Thanks Again, I'll be able to sleep tonight (maybe : ) )!!
> > > Steve
> > >
> > > Mark Stover wrote:
> > >
> > > > Did you enable policy routing? There are two places that you have to
> > "turn
> > > > it on" You need to identify which traffic flows should have policy
> > routing
> > > > applied to them.
> > > >
> > > > Mark
> > > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf
Of
> > > > Steven Weber
> > > > Sent: Saturday, February 10, 2001 9:30 PM
> > > > To: bruce@williamsnetworking.com
> > > > Cc: ccielab@groupstudy.com
> > > > Subject: Re: ccbootcamp lab#1...
> > > >
> > > > what about the poll interval and hello interval commands? I don't
know
> > > why,
> > > > but
> > > > I still cant get this thing to work. When I do a sh route-map I get
0
> > > > matches.
> > > > access-list 100 permit ip any host 10.10.1.5
> > > > access-list 100 permit ip any host 10.10.1.2
> > > > route-map FRAM permit 10
> > > > match ip address 100
> > > > set ip next-hop 10.10.1.1
> > > >
> > > > I can't seem to figure it out.
> > > > Thanks for the help,
> > > > Steve
> > > >
> > > > Bruce Williams wrote:
> > > >
> > > > > The frame-relay map statements that they use are only from each
> > > individual
> > > > > spoke to the hub. That establishes spoke to hub connectivity, but
not
> > > > spoke
> > > > > to spoke connectivity. You have to use a route-map for that
instead of
> > a
> > > > > frame-relay map statement.
> > > > >
> > > > > You could also have use inverse-arp for the hub to spoke
connectivity
> > > > > instead of the map statement, but I assume they want you to become
> > > > familiar
> > > > > with map statements.
> > > > > I also assume that the LMI type of ansi is just to use something
other
> > > > than
> > > > > the default for the sake of practice.
> > > > >
> > > > > Bruce Williams
> > > > >
> > > > > -----Original Message-----
> > > > > From: Steven Weber [mailto:itweber@netzero.net]
> > > > > Sent: Saturday, February 10, 2001 8:41 PM
> > > > > To: ccielab@groupstudy.com
> > > > > Subject: ccbootcamp lab#1...
> > > > >
> > > > > I was looking through the answers to lab#1 and I noticed a few
things:
> > > > > (1) the spoke routers have frame-relay map statements on them.
Isn't
> > the
> > > > > point not to have frame relay map statements on the spoke routers.
(2)
> > > > > that they used the poll-interval and hello interval commands. Are
> > those
> > > > > commands necessary in order to get the lab to work, if so why? (3)
the
> > > > > lmi-type is ansi and not cisco is it necessary to change it or can
it
> > be
> > > > > left at its default.
> > > > > Can someone please shed some light?
> > > > > Thanks,
> > > > > Steve
> > > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:28:45 GMT-3