From: Mike S. Lee (mikele@xxxxxxxxx)
Date: Mon Jan 29 2001 - 18:38:18 GMT-3
In trying to use the Demand circuit option I still see the dialer dialing.
Debugging Q931 is see that the dial cause is 224.0.0.5 which is all spf
routers. I thought that using an ospf demand circuit should have suppressed
all LSA's from going across this line. Can someone either explain this
behavior or provide a working config that uses demand circuits and only
comes up when the primary link fails? Any debug outputs would be helpful as
well.
thanks
mike
At 11:53 AM 1/29/2001 -0800, Kevin Baumgartner wrote:
>I have heard this a few times but I have had no problems using it with OSPF.
>Maybe this was a limitation in earlier 12.0 images.
>
> Kevin
>
>
>At 01:18 PM 1/29/01 -0600, Wade Edwards wrote:
> >As I recall dialer watches work only with IGRP and EIGRP. If you need OSPF
> >then the demand circuit is the best way to go.
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> >Jeremy Gray
> >Sent: Sunday, January 28, 2001 2:34 PM
> >To: ccielab@groupstudy.com
> >Subject: RE: ISDN Backup without the backup interface command?
> >
> >
> >
> >A demand circuit is useful if you really msut run OSPF over an ISDN line.
> >
> >A better answer to this problem is to use a dialer watch-list, a very cool
> >facility used to trigger DDR when a 'watched' route is absent in the routing
> >table.
> >
> >This is great for a number of reasons.
> >
> >1) Packet switched networks are not the best at telling a DTE when there's a
> >problem in the cloud. Examples being ATM and FR
> >Interface may stay up/up even if the remote is down.
> >
> >2) You can place a DDR in a place further into your network rather than on
> >the same router as a critical link and still have DDR work when the link
> >fails if the routes being watches originate beyound the point of failure.
> >
> >Regards,
> >
> >Jeremy.
> >
> >PS: Joined today. Lab date March 8th.
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> >Robert DeVito
> >Sent: 28 January 2001 16:39
> >To: obuba@bellatlantic.net; mac38456@pegasus.cc.ucf.edu;
> >ccielab@groupstudy.com
> >Subject: Re: ISDN Backup without the backup interface command?
> >
> >
> >
> >
> >Another thing to keep in mind is that ospf demand circuit will cause the
> >isdn circuit to come up when there is a topology change.. So don't be
> >shocked when it comes up every once and awhile.
> >
> >Robert
> >
> >----Original Message Follows----
> >From: "Nnanna Obuba" <obuba@bellatlantic.net>
> >Reply-To: "Nnanna Obuba" <obuba@bellatlantic.net>
> >To: "Miguel A. Ciena" <mac38456@pegasus.cc.ucf.edu>,
> ><ccielab@groupstudy.com>
> >Subject: Re: ISDN Backup without the backup interface command?
> >Date: Sun, 28 Jan 2001 10:10:43 -0500
> >
> >That's no trick, use ospf demand circuit
> >
> >
> >Nnanna Obuba, CCIE # 6586
> >www.nantech.com
> >Online lab for CCIE Preparation
> >----- Original Message -----
> >From: "Miguel A. Ciena" <mac38456@pegasus.cc.ucf.edu>
> >To: <ccielab@groupstudy.com>
> >Sent: Sunday, January 28, 2001 9:07 AM
> >Subject: ISDN Backup without the backup interface command?
> >
> >
> > > Between R3 and R5 I got a ISDN link. I want to configure my ISDN to =
> > > back-up my frame relay connection between R3 and R5...Here is the Trick:
> >=
> > > Without using Floating Static and without using the Back-up interface =
> > > command..My Frame and ISDN are in OSPF area 0...
> > >
> > > any ideas..
> > >
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:47 GMT-3