From: Chuck Larrieu (chuck@xxxxxxxxxxxxx)
Date: Wed Jan 10 2001 - 21:44:25 GMT-3
You probably had an easier time concentrating, what with not being
distracted by the anguished moans and sobs of frustration from those around
you. ;->
CONGRATULATIONS!!!!
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Roger Dellaca
Sent: Wednesday, January 10, 2001 4:18 PM
To: ccielab@groupstudy.com
Subject: CCIE #6671
passed last Friday at San Jose!
How it went:
This was my 1st attempt. I flew into San Jose the day before; had a cold,
after landing could hardly hear a thing. Drove to Cisco's site that
afternoon to scout out where I was going. Next morning, had a real tough
time hearing the proctor's instructions. For the 1st hour, I felt like I
was trying to get situated. Read thru everything twice, calmed down around
lunch time, finished day 1 around 3:00, then checked & rechecked. Came back
for day 2, could hear a little better, felt confident, came back for
troubleshooting, then got a post-it with a number.
How I prepared:
All the common books (Doyle, Caslow, Halabi, Kennedy's switching book),
after having completed CCNA/NP/DA/DP using mostly Sybex books, some others
too, certificationzone papers. Started practice labs with most of the CCIE
All-in-one lab study guide, then most of the fatkid.com labs, then most of
the ccbootcamp labs. Used a home lab of 9 routers & 2 days on ccbootcamp
racks. Went thru pretty much all of the 12.0 IOS & Cat5k Config guides &
command references on the doc CD (just skimmed some stuff, read some more
thoroughly, but was familiar with where to go). Did 2 days at the USCS
practice lab. I felt like I had done quite a bit of preparing.
How I approached the lab:
Pretty much the same suggestions as everyone else - read the whole thing
twice, draw your diagram, record stuff about your routers you might need
later, think of possible tricks & traps, move on if stuck on something so
you don't leave any points on the table.
Did a standard set of commands in Notepad to paste in all routers. My
aliases:
alias exec ii sh ip int
alias exec ib sh ip int brief
alias exec ir sh ip route
alias exec xi sh ipx int
alias exec xb sh ipx int brief
alias exec xr sh ipx route
alias exec pr sh ip protocol
alias exec cr clear ip route
alias exec cb clear ip bgp
alias exec b sh ip bgp
alias exec e sh ip eigrp
alias exec o sh ip ospf
alias configure a access-list
for some of these you have multiple uses, for example cb * for all neighbors
or cb <neighbor address> for a specific neighbor (I like typing in b s for
sh ip bgp summary). I practiced with the aliases enough so they wre second
nature.
What I have really heard much, that I find helpful: my method to try to
avoid dumb mistakes, & it's something I tried to practice: when you're
reading thru the lab, plan ahead & think of things, but when you are
configuring, stay "in the moment" & only concentrate on the task being done.
It's like when the wide receiver misses the catch because he starts looking
up the field before the ball is in his hands. Spend a minute after every 2
or 3 tasks, to step back outside of the box & think big picture, but then
get back to focusing on the task being done. Likewise, after having gotten
so far (like 2nd day), don't think back, worry about what's important now.
In summary, I think that first of all preparing A LOT, then not psyching
yourself out, avoiding dumb mistakes, asking the proctor questions, and
skipping over problem sections & coming back to them at the end so as not to
leave sections undone, are the big keys.
What I'm going to do now:
rest.
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:27 GMT-3