dialer map. hub and spoke issues!

From: Claude-Vincent (claude_vincent@xxxxxxxxx)
Date: Fri Jan 05 2001 - 05:01:09 GMT-3

• Next message: Thierry MARTIN: "Rép. : Re: Lab attempt on weekends"
• Previous message: darshan@xxxxxxxxxx: "CCIE 6663"
• Next in thread: Bernard Dunn: "Re: dialer map. hub and spoke issues!"
• Maybe reply: Bernard Dunn: "Re: dialer map. hub and spoke issues!"
• Maybe reply: perez claude-vincent: "Re: dialer map. hub and spoke issues!"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

   
Dear All,

I have a problem with my dialer interfaces. the ios version is 11.2(18) of
the Hub router 2500series.

It is a Hub and spokes topology. I would like to ping R1 and R2 from the hub
using an ISDN line. Please fing hereby the conf. + debug.

If I add dialer pool-member 2 on the bri int. I can ping R2 but not R1. If I
modify on the dialer2, dialer pool 1, same. Moreover, what I don't
understand is why after the outgoing call has been established on the first
B channel, I receive automatically a incoming call from unknown unless I
remove the "dialer pool-member 2" of the bri interface!

I don't want to use static dialer map.

Please help me. I run out of ideas!!!!

interface BRI0
 no ip address
 no ip redirects
 no ip directed-broadcast
 encapsulation ppp
 keepalive 300
 dialer pool-member 1
 no fair-queue
 no cdp enable
 ppp authentication pap chap
!
interface Dialer1
 ip address 192.168.4.65 255.255.255.252
 ip access-group 11 in
 ip access-group 11 out
 no ip redirects
 no ip directed-broadcast
 encapsulation ppp
 no ip split-horizon
 no ip mroute-cache
 dialer remote-name R1
 dialer idle-timeout 90
 dialer string ###
 dialer pool 1
 dialer-group 1
 no fair-queue
 no cdp enable
 ppp pap sent-username ### password ###
!
interface Dialer2
 ip address 10.65.4.65 255.255.255.0
 ip access-group 11 in
 ip access-group 11 out
 encapsulation ppp
 dialer remote-name R2
 dialer idle-timeout 90
 dialer string ###
 dialer pool 2
 dialer-group 1
 ppp authentication chap

ISDN BR0: RX <- SETUP pd = 8 callref = 0x21
        Bearer Capability i = 0x8890
        Channel ID i = 0x8A
        Display i = 'LONG DISTANCE'
        Calling Party Number i = 0x00C3
ISDN BR0: Incoming call id = 0x26B
ISDN BR0: received HOST_INCOMING_CALL
ISDN BR0: Event: Received a call from <unknown> on B2 at 64 Kb/s
ISDN BR0: Event: Accepting the call
%LINK-3-UPDOWN: Interface BRI0:2, changed state to up
ISDN BR0: TX -> CONNECT pd = 8 callref = 0xA1
ISDN BR0: RX <- CONNECT_ACK pd = 8 callref = 0x21
ISDN BR0: Event: Hangup call to call id 0x26B
%ISDN-6-DISCONNECT: Interface BRI0:2 disconnected from ###, call lasted 1
sec
onds

• Next message: Thierry MARTIN: "Rép. : Re: Lab attempt on weekends"
• Previous message: darshan@xxxxxxxxxx: "CCIE 6663"
• Next in thread: Bernard Dunn: "Re: dialer map. hub and spoke issues!"
• Maybe reply: Bernard Dunn: "Re: dialer map. hub and spoke issues!"
• Maybe reply: perez claude-vincent: "Re: dialer map. hub and spoke issues!"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:22 GMT-3