From: fwells12 (fwells12@xxxxxxxxxxx)
Date: Sun Dec 31 2000 - 01:13:40 GMT-3
Download the Router Software Loader. It has everything you need including
instructions.
http://www.cisco.com/public/sw-center/sw-access.shtml
----- Original Message -----
From: Gordon Olson <golson@psn.net>
To: Ronnie Royston <RonnieR@globaldatasys.com>
Cc: <ccielab@groupstudy.com>
Sent: Saturday, December 30, 2000 1:42 PM
Subject: RE: Whoops 2501 IOS upgrade
> Thank you very much for everyones input on this. I was finally able to
boot
> into ROMMON mode and revert back to the old IOS, so that is good. This is
a
> Cisco Pro 2500 and I made a mistake thinking the IOS was the same. Good
> thing I TFTP'd the older IOS.
>
> Robert mentioned that I would need a cookie from Cisco to use the
> traditional IOS, does anyone know how I would go about that? Or is it
> possible that I can buy the IOS for the CPA 2500 somewhere 11.2 or better?
>
> -----Original Message-----
> From: Ronnie Royston [mailto:RonnieR@globaldatasys.com]
> Sent: Saturday, December 30, 2000 12:52 PM
> To: 'Gordon Olson'
> Subject: RE: Whoops 2501 IOS upgrade
>
>
> You may have to Xmodem the new IOS to your router. Search the CCO on how
to
> do this.
>
> -----Original Message-----
> From: Gordon Olson [mailto:golson@psn.net]
> Sent: Saturday, December 30, 2000 11:44 AM
> To: ccielab@groupstudy.com
> Subject: Whoops 2501 IOS upgrade
>
>
> I tried to upgrade the IOS in a 2501 from 10.2 to 11.3 and I am getting
the
> following message.
>
> Verifying checksum... OK (0x1222)
> Flash copy took 0:03:04 [hh:mm:ss]
> fs1(boot)#reload
>
> System configuration has been modified. Save? [yes/no]: n
> Proceed with reload? [confirm]y
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 14336 Kbytes of main memory
>
> F3: 5188960+72956+379796 at 0x3000060
>
> Wrong system software for this hardware
>
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 14336 Kbytes of main memory
>
> F3: 5188960+72956+379796 at 0x3000060
>
> Wrong system software for this hardware
>
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 14336 Kbytes of main memory
>
> F3: 5188960+72956+379796 at 0x3000060
>
> Wrong system software for this hardware
>
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 14336 Kbytes of main memory
>
> I cannot get back to a prompt, anyone know how I get out of this?
>
> Gordon
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:26:13 GMT-3