From: Simon Hopkins (simon@xxxxxxxxxxxxx)
Date: Tue Nov 06 2001 - 11:52:03 GMT-3
I have found that with BT Highway (1 assigned number) if you dial out on 1 B
channel the 2nd B channel on the same router can answer the call so you must
use the "isdn answer1" command to prevent the sending router from answering
the call. I can get it to work 1 way but not both ways......still working on
it.
Simon Hopkins
----- Original Message -----
From: Eddie Jobson <ejobson@thrupoint.net>
To: Horvath, Russell <Russell.Horvath@viatel.com>
Cc: group study <ccielab@groupstudy.com>
Sent: Monday, November 06, 2000 10:06 AM
Subject: Re: Using ISDN S/T Bus for back-to back dialup
> I have a BT ISDN2 circuit at home with one assigned number. If I set the
> dial string as the one number I have been given on the originate router
> I can dial and connect to another BRI interface on another router
> plugged into the second socket. I'm not sure whether it works with any
> call back settings, haven't tried it, but for basic connections it
> appears to be okay. You can however ask BT to present it as two seperate
> 64k's with an individual number assigned.
>
> "Horvath, Russell" wrote:
> >
> > I looked in to this, wanting an ISDN link at home and spilt the ISDN
64K
> > links so I could dial back to back....
> >
> > In the UK BT offer 2 ISDN numbers etc (NOT BT Highway). The only problem
I
> > can think off is whether the D channel can be used to set up the calls
> > together i.e. dial out using 1 64 K line to the other 64 K line.
> >
> > You will be charged per 64 K line as well......
> >
> > If you find the answer then let me know.....
> >
> > regards Russ
> >
> > > ----------
> > > From:
> > > bhackney@netstarnetworks.com[SMTP:bhackney@netstarnetworks.com]
> > > Reply To: bhackney@netstarnetworks.com
> > > Sent: 05 November 2000 22:46
> > > To: group study
> > > Subject: RE: Using ISDN S/T Bus for back-to back dialup
> > >
> > > You can use the isdn answer1 or isdn answer2 to identify to the router
> > > which incoming calls to answer so if you configure each router to
answer a
> > > different number you can do ISDN calls across a single BRI service - I
> > > would imagine that you would be charged call costs.
> > >
> > > Hope that helps,
> > > Bede Hackney.
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > > Justin Menga
> > > Sent: Monday, 6 November 2000 9:11 AM
> > > To: 'Simon Hopkins'; 'ccielab@groupstudy.com'
> > > Subject: RE: Using ISDN S/T Bus for back-to back dialup
> > >
> > >
> > >
> > > I believe this is in the pipeworks - the ISDN Voice BRI Module
for
> > > 17xx/26xx/36xx I think will support ISDN Switching in the near
future.....
> > >
> > > Regards,
> > >
> > > Justin Menga MCSE+I CCNP CCSE ASE
> > > WAN Specialist
> > > Computerland New Zealand
> > > PO Box 3631, Auckland
> > > DDI: (+64) 9 360 4864 Mobile: (+64) 25 349 599
> > > mailto: justin.menga@computerland.co.nz
> > >
> > > -----Original Message-----
> > > From: Simon Hopkins [mailto:simon@muddypaws.net]
> > > Sent: Friday, 26 October 2001 2:54 a.m.
> > > To: ccielab@groupstudy.com
> > > Subject: Using ISDN S/T Bus for back-to back dialup
> > >
> > >
> > > Is it possible to use a single S/T bus to have
back-to-back
> > > dialup for ISDN routers? If so is there any special configuration
required
> > > eg sub-addressing. Also, if you use 1 B channel for a router and the
other
> > > B channel for the 2nd router does this incur call charges from the
> > > supplier.
> > >
> > >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:42 GMT-3