From: dave.awatere@xxxxxxxxxx
Date: Thu Oct 19 2000 - 19:26:16 GMT-3
I just spoke with a PBX techo. He informed me the issue most likely lies with
the old analogue handsets that I am using. The old handsets require the ringer
box which is usually incorporated into the wall outlet. Newer handsets no
longer require this unit as they have the ringer components within. I will pic
k
up a couple of new handsets and try again. Will report back my findings.
R\Davo
---------------------- Forwarded by Dave Awatere/New Zealand/APA/Equant on
10/19/2000 11:06 AM ---------------------------
dave.awatere@equant.com@groupstudy.com on 10/18/2000 02:01:00 PM
Please respond to dave.awatere@equant.com
Sent by: nobody@groupstudy.com
To: ccielab@groupstudy.com
cc:
Subject: RE: Analogue FXS connects OK but phone wont ring
I can connect successfully end to end (from either end) ie. if I pick up the
9000 handset and dial 1000 then pick up the 1000 handset the connection is made
and I can talk to myself. Just can't seem to make the handset ring.
I hiffed a meter on the handset end and can see 30VDC but alas no noise. If I
hiff the meter on the wall outlet I get 50VDC. Suspect JGK is right: the
handset is outside the volt range of an FXS module.
Thanks all\Davo
SYDNOV20\21
"Garcia, Frank" <FGarcia@frk.com> on 10/17/2000 12:54:56 PM
To: "'dave.awatere@equant.com'" <dave.awatere@equant.com>
cc:
Subject: RE: Analogue FXS connects OK but phone wont ring
Just a swag but what happens if you set up the connection in reverse? Do
you get the same results?
Frank
-----Original Message-----
From: dave.awatere@equant.com [mailto:dave.awatere@equant.com]
Sent: Tuesday, October 17, 2000 9:11 PM
To: ccielab@groupstudy.com
Subject: Analogue FXS connects OK but phone wont ring
Can't get the phone to ring. Call connects OK but the phone does not ring.
I
have tried the handsets in wall outlets and they ring just fine.
I also tried changing the ring frequency from 25-50 but still no go. Anyone
else seen this prob?
Cheers\Davo
Handset------FXS2/0/0___r1-------------r2___FXS2/0/0------Handset
Current configuration:
!
hostname r1
!
interface FastEthernet0/0
ip address 1.1.1.1 255.0.0.0
!
voice-port 2/0/0
cptone NZ
!
voice-port 2/0/1
cptone NZ
!
dial-peer voice 1 pots
destination-pattern 1000
port 2/0/0
!
dial-peer voice 2 voip
destination-pattern 9...
session target ipv4:1.1.1.2
!
end
Current configuration:
!
hostname r2
!
interface FastEthernet0/0
ip address 1.1.1.2 255.0.0.0
!
voice-port 2/0/0
cptone NZ
!
voice-port 2/0/1
!
dial-peer voice 1 pots
destination-pattern 9000
port 2/0/0
!
dial-peer voice 2 voip
destination-pattern 1...
session target ipv4:1.1.1.1
!
end
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:27 GMT-3