From: damien (damien@xxxxxxxxxxx)
Date: Sun Oct 15 2000 - 07:47:30 GMT-3
Title: Area 0 interface in OSPF db as Type 5 LSA??
Distribute lists out don't work in OSPF....only distribute lists in
work on the Router they are configured on. However they will only stop
the route from entering the routing table, the LSA will still appear
and be forwarded............
The Type 5 is there because you have the same interface under the the
EIGRP process which is being redistributed and will appear as a type
5......
----- Original Message -----
From: Granofsky, Aaron
To: ccielab@groupstudy.com
Sent: Sunday, October 15, 2000 2:01 AM
Subject: Area 0 interface in OSPF db as Type 5 LSA??
After redistributing OSPF/EIGRP, my serial interface (OSPF Area 0)
shows up as a Type 5 LSA.
What am I missing?
Distribute lists into OSPF don't seem to work.
r2#sh ip os da
OSPF Router with ID (170.10.25.2) (Process ID 1)
<snip>
Type-5 AS External Link States
Link ID ADV Router Age Seq# Checksum Tag
170.10.1.0 170.10.25.2 443 0x80000001 0xDF0 0
here's the config:
!
interface Loopback0
ip address 170.10.25.2 255.255.255.0
no ip directed-broadcast
!
interface FastEthernet0/0
ip address 170.10.26.2 255.255.255.192
no ip directed-broadcast
!
interface Serial0/0
ip address 170.10.1.2 255.255.255.240
no ip directed-broadcast
encapsulation frame-relay
ip ospf network point-to-multipoint
no ip mroute-cache
cdp enable
frame-relay map ip 170.10.1.3 201 broadcast
frame-relay map ip 170.10.1.5 201 broadcast
frame-relay lmi-type ansi
!
interface BRI0/0
bandwidth 64
ip address 170.10.2.2 255.255.255.0
no ip directed-broadcast
encapsulation ppp
dialer idle-timeout 20
dialer map ip 170.10.2.3 name r3 broadcast 5554111
dialer load-threshold 1 either
dialer-group 1
isdn switch-type basic-5ess
ppp authentication chap
ppp multilink
!
router eigrp 1
redistribute ospf 1
passive-interface Serial0/0
passive-interface BRI0/0
network 170.10.0.0
default-metric 1544 100 255 1 1500
distribute-list 4 out ospf 1
distribute-list 2 in
no auto-summary
!
router ospf 1
summary-address 170.10.26.0 255.255.255.0
redistribute eigrp 1 subnets route-map redis
network 170.10.1.0 0.0.0.255 area 0
network 170.10.2.0 0.0.0.255 area 0
default-metric 64
distribute-list 3 in
!
access-list 1 permit 170.10.2.0 0.0.0.255
access-list 2 permit 170.10.25.0 0.0.0.255
access-list 2 permit 170.10.26.0 0.0.0.255
access-list 2 deny any log
access-list 3 deny 170.10.25.0 0.0.0.255 log
access-list 3 deny 170.10.26.0 0.0.0.255 log
access-list 3 permit any
access-list 4 deny 170.10.1.0 log
access-list 4 deny 170.10.1.0 0.0.0.15 log
access-list 4 deny 170.10.1.0 0.0.0.255 log
access-list 4 permit any
dialer-list 1 protocol ip permit
route-map redis deny 10
match ip address 1
!
route-map redis permit 20
!
!
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:27 GMT-3