From: Tony Olzak (aolzak@xxxxxxxxxxxxxxxxxxx)
Date: Wed Oct 11 2000 - 21:37:33 GMT-3
Right. If you leave it off the other end, PPP will automatically create a
dynamic peer route. You won't need the dialer map.
Just don't use a dialer map on the called side.
Tony
----- Original Message -----
From: "Sam Munzani" <sam@munzani.com>
To: "Kevin Baumgartner" <kbaumgar@cisco.com>; "Sanjay Bhakta"
<sbhakta@charter.net>
Cc: <ccielab@groupstudy.com>
Sent: Wednesday, October 11, 2000 2:32 PM
Subject: Re: ISDN Question
> As I said before. It depends on your IOS image. I have done it before
during
> ASET lab in San Jose. Couldn't do it during real lab becase of old IOS. I
> shoose not to use any dialer map on remote router. After connection
dynamic
> took care of it.
>
> Sam
> > Not sure why you say that this can't be done? I have used it this way
> > before. Maybe it's a image problem, but to be honest I haven't seen
> anything
> > like this or ran into this kind of problem.
> >
> > Kevin
> >
> > At 11:11 AM 10/11/00 -0500, you wrote:
> > >It does not look like you can enter a dialer map without dialer string
on
> > >legacy ddr.
> > >
> > >Sanjay Bhakta (RTP 10/18)
> > >sbhakta@charter.net
> > >sanjaybhakta@hotmail.com
> > >----- Original Message -----
> > >From: "Derek Buelna" <dameon@aracnet.com>
> > >To: <ccielab@groupstudy.com>
> > >Sent: Wednesday, October 11, 2000 1:13 AM
> > >Subject: RE: ISDN Question
> > >
> > >
> > > > I was under the impression you could do this:
> > > >
> > > > Legacy: physical interface - dialer map with a dial string on one
end
> and
> > >no
> > > > dial string on the other.
> > > > DDR: dialer interface - no map of course - no dial string on one end
> as
> > > > above.
> > > >
> > > > If he doesn't have a dial string, he can't call, right?
> > > > I guess the debugs would say that he would try and call but no dial
> > >string.
> > > >
> > > > Do any of you have any thoughts on this?
> > > > It is obviously important to have this configured properly so that
> only
> > >one
> > > > side will ever try to dial.
> > > >
> > > > -Derek
> > > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > > > Daniel Keller
> > > > Sent: Tuesday, October 10, 2000 7:50 PM
> > > > To: sbhakta@charter.net; ccielab@groupstudy.com
> > > > Subject: Re: ISDN Question
> > > >
> > > > Do this on the non-calling router:
> > > >
> > > > Int bri0
> > > > dialer-group 1
> > > >
> > > >
> > > > dialer-list 1 protocol ip deny
> > > >
> > > > Then no traffic will ever trigger a call.
> > > >
> > > > Dan Keller
> > > >
> > > >
> > > > >>> "Sanjay Bhakta" <sbhakta@charter.net> 10/10/00 09:31PM >>>
> > > > It is possible to set one side to be the calling and we will not
have
> to
> > >use
> > > > dialer maps on the called router for IP and IPX. The IOS will
create
> > >dialer
> > > > maps dynamically.
> > > >
> > > > What if you are also routing appletalk or decnet over ISDN and you
> want to
> > > > make sure only one side will be initiating calls. I suppose we can
> create
> > > > dialer maps on the called router with a wrong dialer string, which I
> have
> > > > done and seems to work fine.
> > > >
> > > > Is there another way?
> > > >
> > > > ********
> > > > Sanjay Bhakta (Halifax 10/18)
> > > > sbhakta@charter.net
> > > > sanjaybhakta@hotmail.com
> > > >
> > > >
> > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:25 GMT-3