From: Derek Buelna (dameon@xxxxxxxxxxx)
Date: Thu Sep 28 2000 - 20:48:24 GMT-3
Make sure to get the bootcamp labs..
-Derek
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Lampron, George
Sent: Thursday, September 28, 2000 4:27 PM
To: ccielab@groupstudy.com
Subject: Building Lab
Okay folks,
Maybe someone can provide some guidance.
I've gotten to the point that I have out together some equipment for a Lab
I have the following:
5500 Switch with RSM, 24 port ethernet and GBIC uplink module
5505 Switch, 24 port ethernet and GBIC uplink module
3640 router
3620 router
4 - 2620 routers
as 5300
pix 520
I would like some suggestions as to books or resources with practice labs
and if there are any other piece of equipment I shoul add to my CCIE lab.
George
-----Original Message-----
From: Mark Lewis [mailto:markl11@hotmail.com]
Sent: Thursday, September 28, 2000 1:15 PM
To: jheneyccie@hotmail.com; ccielab@groupstudy.com
Subject: Re: While we're on the subject of ATM....!
Hi,
Yep,you're right.I wasn't thinking.
The issue is the old half bridge issue - you've got to have a bridge at both
ends...
Mark
>From: "Jack Heney" <jheneyccie@hotmail.com>
>To: markl11@hotmail.com, ccielab@groupstudy.com
>Subject: Re: While we're on the subject of ATM....!
>Date: Thu, 28 Sep 2000 18:47:05 GMT
>
>
>Actually, it won't work if the IP address is right on the router
>interface...I ran into this problem a few weeks ago (I had the address
>right on the ATM interface)...Both ends of the point-to-point vc must be
>performing the same operation (routing or bridging)...Since the CAT is
>bridging traffic from the backplane to the virtual circuit, the other end
>of the VC (the router interface) must be bridged as well.
>
>Jack Heney
>
>>From: "Mark Lewis" <markl11@hotmail.com>
>>Reply-To: "Mark Lewis" <markl11@hotmail.com>
>>To: ccielab@groupstudy.com
>>Subject: While we're on the subject of ATM....!
>>Date: Thu, 28 Sep 2000 17:25:55 GMT
>>
>>
>>MAY be useful (or maybe not!).
>>
>>How to configure ATM on the cat LANE module without LANE (!!)
>>
>>Take a simple topology like this:
>>
>> R-----LS-----Cat
>>
>>
>>Config the router as per usual for a pvc to the cat (lane module) (having
>>set up the pvc on the ls first of course).
>>
>>Then config you cat LANE module like this:
>>
>>int atm0
>>
>>atm VCD VPI VCI aal5snap
>>atm bind pvc vlan VCD VLAN#
>>
>>(replacing the VCD,VPI,VCI, and VLAN#) with the appropriate numbers.
>>
>>Put an ip addr. on the router, put the cat sc0 int into the vlan as
>>indicated by the VLAN# above, and ta-dah... you are now able to ping the
>>cat
>>from the router & visa-versa!
>>
>>(By the way, when I did it, I bridged through the atm int on the router to
>>an ip addr on a bvi (irb), but I don't see any reason it won't work if
>>you
>>put the ip address directly on the atm int).
>>
>>Interesting, huh?
>>
>>
>>Mark
>>
>>
>>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:08 GMT-3