From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Wed Sep 13 2000 - 01:20:01 GMT-3
If you have a lot of changes in OSPF Topology the OSPF hello packets
will be sent across the OSPF demand circuit and the ISDN line will
always be up. Try doing a 'debug ip ospf adj" to see what's happening.
Are you doing any redistribution?
Kevin
>
> The problem I have is if the demand circuit is not in area 0, the line
> always be activited by OSPF hello packet. I can see the hello packet has
> been suppressed when I do "show ip ospf int bri 0". But the line always be
> up and can't keep quiet for a while. Move it to area 0, I can see the isdn
> demand line keep quiet and just be activated on demand. Is this the way that
> ISDN demand circuit works with non-backbone area??? How can I verify this???
>
> Thanks again,
> Rena
>
>
> >From: "Feliz, Edgar" <Edgar.Feliz@BTNA.com>
> >Reply-To: "Feliz, Edgar" <Edgar.Feliz@BTNA.com>
> >To: Lachlan_Kidd@data3.com.au, aiqun hu <huaq@hotmail.com>
> >CC: ccielab@groupstudy.com
> >Subject: RE: OSPF demand-circuit over OSPF no backbone area
> >Date: Tue, 12 Sep 2000 18:01:06 -0400
> >
> >That is not correct, it does work even if you are not in area 0. In the
> >case
> >of the CCBOOTCAMP labs I was able to make mine work fine.
> >
> >EF
> >
> >-----Original Message-----
> >From: Lachlan_Kidd@data3.com.au [mailto:Lachlan_Kidd@data3.com.au]
> >Sent: Tuesday, September 12, 2000 2:54 AM
> >To: aiqun hu
> >Cc: ccielab@groupstudy.com
> >Subject: Re: OSPF demand-circuit over OSPF no backbone area
> >
> >
> >
> >Hi Rena,
> > I haven't tried this myself, but in the bootcamp labs, mention is
> >made
> >to the effect that it (the on demand circuit) does not work if you are not
> >in area 0.
> >Lachlan
> >
> >
> >
> >
> > "aiqun hu"
> >
> > <huaq@hotmail To: ccielab@groupstudy.com
> >
> > .com> cc:
> >
> > Sent by: Subject: OSPF demand-circuit
> >over OSPF no backbone area
> > nobody@groups
> >
> > tudy.com
> >
> >
> >
> >
> >
> > 12/09/00
> >
> > 01:35 PM
> >
> > Please
> >
> > respond to
> >
> > "aiqun hu"
> >
> >
> >
> >
> >
> >
> >
> >
> >Hello guys,
> >
> >Tested OSPF demand circuit in my lab. But I can't make the demand circuit
> >over no backbone area(not area 0) working. Changed it to area 0, it
> >works!!!! Is there any specific command I should do for non backbone
> >area???
> >How about demand circuit over OSPF virtual-link? Anybody has some config
> >for
> >these two scenario? I greatly appreciate your help.
> >
> >Thanks again,
> >Rena
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:55 GMT-3