From: Sam Munzani (sam@xxxxxxxxxx)
Date: Thu Aug 31 2000 - 18:07:36 GMT-3
Actually I tried,
sh run int s0/0 with 12.0 code without using begin command and it just
pulled information for s0/0 interface.
Sam
On Thu, 31 Aug 2000, Lee, Mike wrote:
> If you are running 12.0 code you can use the command "show running | begin
> interface X" in order to bypass the rest of the config. The output modifiers
> are really useful for this.
>
> Mike Lee
> CCNP+ATM+Security+Voice/CCDP/NNCSE/NNCDE
> Customer Engineer
> (512)340-3413
>
>
>
> -----Original Message-----
> From: Kevin M. Woods [mailto:kev@nil.org]
> Sent: Thursday, August 31, 2000 3:25 PM
> To: Dana.L.Steffey@seagate.com
> Cc: Tony Medeiros; sam@chinet.com; kbaumgar@cisco.com;
> ccielab@groupstudy.com
> Subject: Re: My favorate alias commands (was Inverse ARP and
> Subinterfaces)
>
>
> Add running to the command, e.g. "s run int f1/0".
>
> Kevin
>
> // Tony -
> //
> // Can you check your command where you say a "s inter f1/0" shows you a the
> // running config for that interface only.
> //
> // "show interface f1/0" - on every IOS I have ever worked on including the
> // 12.0.9 that I am working on now gives me the stat's for the interface,
> not
> // the running config.
> //
> // i.e.
> //
> // NRM-Hub#sh int et4/0
> // Ethernet4/0 is up, line protocol is up
> // Hardware is cxBus Ethernet, address is 0060.7089.a880 (bia
> // 0060.7089.a880)
> // Description: Link to NW5 EDS FW
> // Internet address is 192.168.95.1/24
> // MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
> // Encapsulation ARPA, loopback not set, keepalive set (10 sec)
> // ARP type: ARPA, ARP Timeout 04:00:00
> // Last input 00:00:07, output 00:00:07, output hang never
> // Last clearing of "show interface" counters 2w1d
> // Queueing strategy: fifo
> // Output queue 0/300, 0 drops; input queue 0/300, 0 drops
> // 5 minute input rate 3000 bits/sec, 2 packets/sec
> // 5 minute output rate 2000 bits/sec, 3 packets/sec
> // 1308510 packets input, 660949993 bytes, 0 no buffer
> // Received 3 broadcasts, 0 runts, 0 giants, 0 throttles
> // 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> // 0 input packets with dribble condition detected
> // 1409375 packets output, 237615987 bytes, 0 underruns
> // 0 output errors, 252 collisions, 0 interface resets
> // 0 babbles, 0 late collision, 0 deferred
> // 0 lost carrier, 0 no carrier
> // 0 output buffer failures, 0 output buffers swapped out
> //
> // I would be really interested in a command that would show me the running
> // config for a specific interface because pressing the space bar through
> some
> // of the running configs on my 7513's get's old real fast.
> //
> // Thanks,
> //
> // Dana Steffey, CCNP, CCNP-Voice, CCDP, CCNA WAN Switching, MCSE, MCT, CNA,
> // Electrical Engineer
> // 2nd Lab attempt: November 1st, Halifax
> // Seagate Technology
> // Minneapolis, MN
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:34 GMT-3