From: Earl Aboytes (earl@xxxxxxxxxxxx)
Date: Thu Aug 17 2000 - 03:04:06 GMT-3
Is your mac address a.a.a? You need to use the mac address. The "ipx
routing a.a.a" command only assigns the serial interfaces. Do a show
interface and get the bia of the Ethernet and prepend the 1 to it. That
should work.
Remember, IPX uses the mac address as the host portion of the address.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Earl Aboytes CCIE #6097
Senior Technical Consultant
GTE Managed Solutions
805-381-8817
earl.aboytes@verizon.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Harbir Kohli
Sent: Wednesday, August 16, 2000 7:24 PM
To: 'Ccielab
Subject: IPX Ping
Hello Group
Why can I not ping my own ethernet interface ?
The interface is up, and I can ping my serial interface
*****************
RTA#ping 2.a.a.a
Type escape sequence to abort.
Sending 5, 100-byte IPX cisco Echoes to 2.000a.000a.000a, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/9/12 ms
********************
RTA#ping 1.a.a.a
Type escape sequence to abort.
Sending 5, 100-byte IPX cisco Echoes to 1.000a.000a.000a, timeout is 2
seconds:
*Feb 28 19:26:19.391 est: IPX: local:1.0000.0c06.94b5->1.000a.000a.000a
ln=100 t
c=00, gw=Et0:1.000a.000a.000a.
*Feb 28 19:26:21.387 est: IPX: local:1.0000.0c06.94b5->1.000a.000a.000a
ln=100 t
c=00, gw=Et0:1.000a.000a.000a.
*Feb 28 19:26:23.387 est: IPX: local:1.0000.0c06.94b5->1.000a.000a.000a
ln=100 t
c=00, gw=Et0:1.000a.000a.000a.
*Feb 28 19:26:25.387 est: IPX: local:1.0000.0c06.94b5->1.000a.000a.000a
ln=100 t
c=00, gw=Et0:1.000a.000a.000a.
*Feb 28 19:26:27.387 est: IPX: local:1.0000.0c06.94b5->1.000a.000a.000a
ln=100 t
c=00, gw=Et0:1.000a.000a.000a.
Success rate is 0 percent (0/5)
*******************
hostname RTA
!
!
ip subnet-zero
no ip domain-lookup
ipx routing 000a.000a.000a
clock timezone est -5
clock summer-time edt recurring
*****************
RTA#sh ipx int brief
Interface IPX Network Encapsulation Status
IPX State
Ethernet0 1 NOVELL-ETHER up
[up]
Loopback0 5 UNKNOWN up
[up]
Serial0 2 HDLC up
[up]
Serial1 unassigned not config'd up
n/a
***************
RTA#sh ipx ro
Codes: C - Connected primary network, c - Connected secondary network
S - Static, F - Floating static, L - Local (internal), W - IPXWAN
R - RIP, E - EIGRP, N - NLSP, X - External, A - Aggregate
s - seconds, u - uses
5 Total IPX routes. Up to 1 parallel paths and 16 hops allowed.
No default route known.
C 1 (NOVELL-ETHER), Et0
C 2 (HDLC), Se0
C 5 (UNKNOWN), Lo0
R 3 [07/01] via 2.000b.000b.000b, 52s, Se0
R 4 [13/02] via 2.000b.000b.000b, 52s, Se0
*************************
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:27 GMT-3