From: Sam Munzani (sam@xxxxxxxxxx)
Date: Thu Jul 20 2000 - 09:48:30 GMT-3
Without any config just do "no shut" on interface. This has to activate
layer 1 if you have line working and proper patch cord. Nothing else you
can do on your end to fix it. Call Telco.
On Wed, 19 Jul 2000 Richard_Woo@infonet.com wrote:
> Padhu,
>
> If you haven't already, check the following:
> * BRI port type ( U or S/T)
> * ISDN Switch type (try different type)
> * Cable from the BRI port to the jack. (straight thru, not cross over)
>
> I had a problem with my home ISDN switch type. Telco told me to use
> certain type, but it didn't work.
> I tried other types and found one that worked. Later on, I found out that
> it was a common thing among the users.
> If the layer 1 isn't working, I woudn't even bother trying other stuff like
> SPID#.
> Hope this helped.
>
> Richard
>
>
>
>
>
> "Wojtek Iwanczyk" <WIwanczyk@exenet.com> on 07/18/2000 11:04:54 AM
>
> Please respond to "Wojtek Iwanczyk" <WIwanczyk@exenet.com>
>
> To: ccielab@groupstudy.com, Padhu@steinroe.com
> cc: (bcc: Richard Woo/HQ/ISC)
>
> Subject: Re: ISDN layer-1 deactivated
>
>
>
>
> Check with the TECO.... Is it an extended demark ?? if so check the pin
> outs ...
>
> Wojtek Iwanczyk
> Sr Support Engineer
> Exenet Technologies
> 15 E 26th Street
> New York, NY 10010
> (212) 684 7300
> wiwanczyk@exenet.com
>
>
> >>> <Padhu@steinroe.com> 07/18/00 01:40PM >>>
>
> I have 2 new BRI ISDN lines. Had the ckt extened to my office and plugged
> into 2503's BRI port.configured basic-5ess as switch type...reloaded and
> tried and sh int bri0
> shows i/f up but spoofing ...I took the router over to the demark and
> connect the router directly and it still didnt work. layer-1 deactivated.
>
> I am using a 2503 ..It has a BRI port..Am i missing something or should i
> work with the telco ? Thanks .
>
> Cheers,Padhu
>
> newyork#sh isdn status
> The current ISDN Switchtype = basic-5ess
> ISDN BRI0 interface
> Layer 1 Status:
> DEACTIVATED
> Layer 2 Status:
> Layer 2 NOT Activated
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Activated dsl 0 CCBs = 0
> Total Allocated ISDN CCBs = 0
> newyork#sh int bri0
> BRI0 is up, line protocol is up (spoofing)
> Hardware is BRI
> MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
> Encapsulation PPP, loopback not set
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0 (size/max/drops); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/0/256 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 collisions, 9 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 0 carrier transitions
>
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:56 GMT-3