From: Earl Aboytes (earl@xxxxxxxxxxxx)
Date: Tue Jun 27 2000 - 21:28:33 GMT-3
The real problem here is that you are using virtual phone numbers. Look at you
r spids. They are 0835866101 and so forth. Change your dialer maps appropriat
ely and it will work. R1 should look like the following:
interface BRI0
ip address 122.11.1.1 255.255.255.0
no ip directed-broadcast
encapsulation ppp
dialer map ip 122.11.1.2 name R6 8358662
dialer load-threshold 1 either
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866101
isdn spid2 0835866301
no cdp enable
ppp multilink
It should work after that.
--Earl
---------- Original Message ----------------------------------
From: Kevin Baumgartner <kbaumgar@cisco.com>
Reply-To: Kevin Baumgartner <kbaumgar@cisco.com>
Date: Tue, 27 Jun 2000 16:33:13 -0700
>Are you trying to ping the local router or the remote router?
>If you are talking about the remote router which is really what you need
>to test how can this work no ip address assigned?
>
> Kevin
>
>At 06:17 PM 6/27/00 -0500, you wrote:
>>Kevin,
>>At this point I don't warry about interesting traffic, I just want to have
>>int bri0 in up/up state. you should be able to do this even with no ip
>>adresses assigned and no dialer-groups defined.
>>
>>-----Original Message-----
>>From: Kevin Baumgartner [mailto:kbaumgar@cisco.com]
>>Sent: Tuesday, June 27, 2000 6:12 PM
>>To: Zaitsev DN (Dmitry)
>>Cc: ccielab@groupstudy.com
>>Subject: Re: Teltone config problem
>>
>>
>>You need also "dialer-group 1" on R6. Otherwise interesting traffic
>>will not to be forwarded in or out of BRI interface.
>>
>> This a common thing that a lot of people make the mistake on when
>>doing ISDN. You need a dialer-group on the caller - R1 and also the
>>receiver - R6.
>>
>> Kevin
>>
>>
>>At 05:38 PM 6/27/00 -0500, you wrote:
>> >I am using a Teltone Demonstrator to simulate BRI.
>> >
>> >R1-----Teltone-----R6
>> >
>> >R1#
>> >interface BRI0
>> > ip address 122.11.1.1 255.255.255.0
>> > encapsulation ppp
>> > dialer map ip 122.11.1.2 name R6 18008358662
>> > dialer load-threshold 1 either
>> > dialer-group 1
>> > isdn spid1 0835866101
>> > isdn spid2 0835866301
>> > no cdp enable
>> > ppp multilink
>> >
>> >dialer-list 1 protocol ip permit
>> >
>> >R6#
>> >interface BRI0
>> > ip address 122.11.1.2 255.255.255.0
>> > encapsulation ppp
>> > dialer map ip 122.11.1.1 name R1
>> > dialer load-threshold 1 either
>> > isdn switch-type basic-ni
>> > isdn spid1 0835866201
>> > isdn spid2 0835866401
>> > ppp multilink
>> >
>> >By pinging 122.11.1.2 from R1, I can get BRI0:1 and BRI0:2 to connect but
>> >interface bri0 still in spoofing state and of course no ping replies.
>> >Teltone is in basic-Ni1 mode.
>> >How do I put interface bri0 in up/up mode?
>> >Thanks
>> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:43 GMT-3