From: chenhao (chenhao@xxxxxxxxxxxxxxxx)
Date: Wed Jun 07 2000 - 14:39:09 GMT-3
Hello:
The dialer watch is designed for EIGRP/IGRP over DDR and just for IP,
2611 can do it,it can work with Async port, the following information is
from CD:
Dialer Watch provides reliable connectivity without relying solely on
defining interesting traffic to trigger outgoing calls at the
central router. Dialer Watch uses the convergence times and characteristics
of dynamic routing protocols. Integrating backup
and routing features enables Dialer Watch to monitor every deleted route. By
configuring a set of watched routes that define
the primary interface, you are able to monitor and track the status of the
primary interface as watched routes are added and
deleted. Monitoring the watched routes is done in the following sequence:
1. Whenever a watched route is deleted, Dialer Watch checks to see if
there is at least one valid route for any of the
defined watched IP addresses.
2. If no valid route exists, the primary line is considered down and
unusable.
3. If a valid route exists for at least one of the defined IP
addresses, and if the route is pointing to an interface other than
the backup interface configured for Dialer Watch, the primary link is
considered up.
4. In the primary link goes down, Dialer Watch is immediately notified
by the routing protocol and the secondary link is
brought up.
5. Once the secondary link is up, at the expiration of each idle
timeout, the primary link is rechecked.
6. If the primary link remains down, the idle timer is indefinitely
reset.
7. If the primary link is up, the secondary backup link is
disconnected. Additionally, you can set a disable timer to create
a delay for the secondary link to disconnect, after the primary link is
reestablished.
Good Luck!
chenhao
----- Original Message -----
From: <abdul_rahim@ccsi.canon.com>
To: chenhao <chenhao@snm.szptt.net.cn>
Cc: <ccielab@groupstudy.com>
Sent: Thursday, June 08, 2000 1:02 AM
Subject: Re: DDR config with EIGRP and OSPF
> Hi
> I read the basic prerequisitives of it and it said that
> The router must have an NT1 or T1 attach to it which supports V.25 bis
> signalling
> But I do have a BRI U port on my 2611
> Do you think it will work ?
> The rest concept seems that using this dialer watch I can use EIGRP with
> DDR
> Looking back for your feedback
> Thanks
> Abdul
>
>
>
>
> "chenhao" <chenhao@snm.szptt.net.cn> on 06/07/2000 06:45:01 AM
>
> Please respond to "chenhao" <chenhao@snm.szptt.net.cn>
>
> To: ccielab@groupstudy.com
> cc: (bcc: Abdul Rahim/IS Operations/Operations/CCSI)
> Subject: Re: DDR config with EIGRP and OSPF
>
>
>
>
> hello,abdul_rahim:
> You can use the Dialer watch. See the following URL:
>
>
http://127.0.0.1:8080/cc/td/doc/product/software/ios113ed/113t/113t_2/dwatc
> h
> .htm
>
> Best regards!
>
>
>
> ----- Original Message -----
> From: <abdul_rahim@ccsi.canon.com>
> To: <ccielab@groupstudy.com>
> Sent: Wednesday, June 07, 2000 4:52 AM
> Subject: DDR config with EIGRP and OSPF
>
>
> > Hi Can any body forward me some DDR configs with EIGRP
> > Thanks
> > Abdul
> >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:41 GMT-3