From: LESH, MIKE (MIKLES@xxxxxxxxxx)
Date: Thu Mar 23 2000 - 17:36:14 GMT-3
Derek,
If you use the escape-character xxx command on the aux 0 line, and
make xxx something like 26, the escape sequence will be ^zx. however, I have
noticed that this command works better on the actual terminal lines of the
access server then on the console ports. I don't know about how it would
work on the Aux port. Also, when you do a show line x command it will tell
you what the escape sequence is for the line, thus a little playing with
numbers in the 2x range may find you a key sequence you like better.
Have fun,
Mike
----------
From: Derek Small (Fuse)[SMTP:dwsmall@fatkid.com]
Reply To: Derek Small (Fuse)
Sent: Thursday, March 23, 2000 11:56 AM
To: CCIE Lab
Subject: Re: casscade reverse telnet?
I don't think I did a very good job asking this one.
I have the following specific scenario. A terminal server,
Term_Srv, a
2509, is used to access the console port of another router R3 though
reverse
telnet. There is a roll-over cable on the AUX port of R3 that
connects to
router R4. When you open a reverse telnet from R3 to R4, you cannot
use the
default escape sequence of cntl-shift-6,x to return to R3's console
from R4.
That escape sequence takes you back to the Term_Srv prompt. Is
there a way
to specifiy a different escape sequence on the AUX port of R3 so
that you
could for instance type cntl-shift-7,x or something else, that would
take
you from R4 back to R3.
With a sniffer I captured the default cntl-shift-6,x sequence and
found the
cntl-shift-6 part, sent an ASCII character with a decimal value of
30 to the
Term_Srv router. This is also the default value for the escape
character on
the AUX port. I then captured a few other escape sequences with my
telnet
client and tried using those values (after converting from hex) but
none of
them had any effect, I stayed on the R4 prompt. Does anyone have
any
experience using ALTERNATE escape sequences so that you could type
one thing
to go back to R3 from R4 and the standard sequence to go from R4
clear back
to the Term_Srv.
Thanks
Derek Small
dwsmall@fatkid.com
----- Original Message -----
From: GRIZZUTI Javier <jgrizzut@softnet.com.ar>
To: Derek Small (Fuse) <dwsmall@fatkid.com>
Sent: Thursday, March 23, 2000 2:03 PM
Subject: RE: casscade reverse telnet?
> Try with ctrl-shift-66 ( the six twice)
>
> Javier
>
>
>
> > -----Original Message-----
> > From: Derek Small (Fuse) [SMTP:dwsmall@fatkid.com]
> > Sent: Thursday, March 23, 2000 2:13 PM
> > To: CCIE Lab
> > Subject: Re: casscade reverse telnet?
> >
> > Does anyone have any experience getting this to work. I've
tried
several
> > alternate escape sequences and nothing seems to work.
> >
> > I used a sniffer to identify a few alternate escape sequences
that
Windows
> > Telnet client sends out by default. Then converted them from
HEX and
> > tried
> > them on the reverse telnet port (AUX 0), but could not break out
of the
> > second routers's console port.
> >
> > Thank You
> >
> > Derek Small
> > dwsmall@fatkid.com
> >
> >
> > ----- Original Message -----
> > From: Derek A. Buelna <dameon@aracnet.com>
> > To: 'Michael Law' <htluo@cisco.com>; CCIE Lab
<ccielab@groupstudy.com>
> > Cc: <dameon@aracnet.com>
> > Sent: Wednesday, February 23, 2000 8:53 PM
> > Subject: RE: casscade reverse telnet?
> >
> >
> > Hi,
> >
> > Use different escape sequences on the different routers.
> > The command is escape-character. Use it on lines.
> >
> > -Derek
> >
> > -----Original Message-----
> > From: Michael Law [SMTP:htluo@cisco.com]
> > Sent: Wednesday, February 23, 2000 5:05 PM
> > To: CCIE Lab
> > Subject: casscade reverse telnet?
> >
> > << File: ATT00000.htm >> I telnet from R1's AUX port to R2's
CON port,
> > and
> > then telnet from R2's AUX port to R3's CON port.
> > Now, I press CTRL-SHIFT-6, I go back to R1.
> > Is there any way I can get back from R3 to R2, not the R1?
> >
> > Michael
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:06 GMT-3