From: Khurram Khani (ajmal@xxxxxxxxxxxxxxx)
Date: Tue Feb 15 2000 - 03:45:31 GMT-3
I rebooted all the 3 routers and it works ????? Save me.!
----- Original Message -----
From: Khurram Khani <ajmal@emirates.net.ae>
To: <ccielab@groupstudy.com>
Sent: Monday, February 14, 2000 9:25 PM
Subject: Appletalk on NBMA
> Hello.
>
> Problem, I am not getting Router 1 Ethernet 0 route advertisment in
> Router2 and Router 3. Router 1 is advertsing cable-range 1-10 on
> Framerelay cloud but other Routers not receiving it ??
>
> Router 2 ---> HUB (I have put 'no appletalk eigrp-splithorizon and
> 'appletalk local-routing' instruction)
>
> Router 1 ---> Spoke
> Router 3 ---> Spoke
>
>
> Router 1 has one "eth 0" and one se2.1 point-to-point
> Router 2 has one "eth 0" and one se2.1 multipoint
> Router 3 has one "eth 0" and one se2.1 point-to-point
>
>
> Configurations
> ----
>
> router 1
>
> appletalk routing eigrp 2
> appletalk route-redistribution
> appletalk local-routing
>
> int eth 0
> appletalk cable-range 1-10 1.1
> appletalk zone Router1Ethernet
> no shut
>
> int se2.1 point-to-point
> appletalk cable-range 100-100 100.2
> appletalk zone FrameRelay
> appletalk protocol ei
> no appletalk protocol rtmp
>
>
> Router 2
> ----------
>
> appletalk routing eigrp 1
> appletalk route-redistribution
> appletalk local-routing
>
> int eth 0
> appletalk cable-range 11-20 11.1
> appletalk zone Router2Ethernet
> no shut
>
> int se2.1 multipoint
> appletalk cable-range 100-100 100.1
> appletalk zone FrameRelay
> frame-relay map apple 100.2 101 bro
> frame-relay map apple 100.3 104 bro
> appletalk protocol ei
> no appletalk protocol rtmp
> no appletalk eigrp-splithorizon
>
> Router 3
> --------
> appletalk routing eigrp 3
> appletalk route-redistribution
> appletalk local-routing
>
> int eth 0
> appletalk cable-range 30-30 30.1
> appletalk zone Router3Ethernet
> no shut
>
> int se2.1 point-to-point
> appletalk cable-range 100-100 100.3
> appletalk zone FrameRelay
> appletalk protocol ei
> no appletalk protocol rtmp
>
>
>
>
>
>
> router1#
> router1#
>
> (Notice 1-10 is advertised on Se2.1 but other routers are not receving it)
> ---
>
> 02:44:42: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
>
> 02:44:42: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
> 02:44:44: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
> 02:44:44: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
> 02:44:47: AT: atigrp2_rtdelete, deleting 100-100 from 100.1 on Serial2.1
> 02:44:47: AT: atigrp2_rtupdate, metric 23284736 succ 1 for 100-100, is:
> 100.1, n
> h: 100.1, idb: Serial2.1
> 02:44:47: AT: atigrp2_rtdelete, deleting 30-30 from 100.1 on Serial2.1
> 02:44:47: AT: atigrp2_rtupdate, metric 23310336 succ 0 for 30-30, is:
100.1,
> nh:
> 100.1, idb: Serial2.1
> 02:44:47: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
> 02:44:47: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
>
>
>
> router2(config)#end
> router2#
> 02:51:19: %SYS-5-CONFIG_I: Configured from console by console
> router2#sh apple ro
> Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP
> S - static P - proxy
> 3 routes in internet
>
> The first zone listed for each entry is its default (primary) zone.
>
> C Net 11-20 directly connected, Ethernet0, zone Router2Ethernet
> E Net 30-30 [1/G] via 100.3, 1171 sec, Serial2.1, zone Router3Ethernet
> C Net 100-100 directly connected, Serial2.1, zone FrameRelay
> router2#
>
> router3#
> router3#sh apple ro
> Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP
> S - static P - proxy
> 3 routes in internet
>
> The first zone listed for each entry is its default (primary) zone.
>
> E Net 11-20 [1/G] via 100.1, 1185 sec, Serial2.1, zone Router2Ethernet
> C Net 30-30 directly connected, Ethernet0, zone Router3Ethernet
> C Net 100-100 directly connected, Serial2.1, zone FrameRelay
> router3#
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:22:53 GMT-3