From: zhencai (zhencai@xxxxxxxx)
Date: Mon Feb 14 2000 - 15:05:38 GMT-3
Hi,
On spoke routers, put "frame-relay interface-dlci xxx" command.
Regards,
Zhen Cai
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Khurram Khani
Sent: Monday, February 14, 2000 9:25 PM
To: ccielab@groupstudy.com
Subject: Appletalk on NBMA
Hello.
Problem, I am not getting Router 1 Ethernet 0 route advertisment in
Router2 and Router 3. Router 1 is advertsing cable-range 1-10 on
Framerelay cloud but other Routers not receiving it ??
Router 2 ---> HUB (I have put 'no appletalk eigrp-splithorizon and
'appletalk local-routing' instruction)
Router 1 ---> Spoke
Router 3 ---> Spoke
Router 1 has one "eth 0" and one se2.1 point-to-point
Router 2 has one "eth 0" and one se2.1 multipoint
Router 3 has one "eth 0" and one se2.1 point-to-point
Configurations
----router 1
appletalk routing eigrp 2 appletalk route-redistribution appletalk local-routing
int eth 0 appletalk cable-range 1-10 1.1 appletalk zone Router1Ethernet no shut
int se2.1 point-to-point appletalk cable-range 100-100 100.2 appletalk zone FrameRelay appletalk protocol ei no appletalk protocol rtmp
Router 2 ----------
appletalk routing eigrp 1 appletalk route-redistribution appletalk local-routing
int eth 0 appletalk cable-range 11-20 11.1 appletalk zone Router2Ethernet no shut
int se2.1 multipoint appletalk cable-range 100-100 100.1 appletalk zone FrameRelay frame-relay map apple 100.2 101 bro frame-relay map apple 100.3 104 bro appletalk protocol ei no appletalk protocol rtmp no appletalk eigrp-splithorizon
Router 3 -------- appletalk routing eigrp 3 appletalk route-redistribution appletalk local-routing
int eth 0 appletalk cable-range 30-30 30.1 appletalk zone Router3Ethernet no shut
int se2.1 point-to-point appletalk cable-range 100-100 100.3 appletalk zone FrameRelay appletalk protocol ei no appletalk protocol rtmp
router1# router1#
(Notice 1-10 is advertised on Se2.1 but other routers are not receving it) ---
02:44:42: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
02:44:42: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1 02:44:44: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1 02:44:44: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1 02:44:47: AT: atigrp2_rtdelete, deleting 100-100 from 100.1 on Serial2.1 02:44:47: AT: atigrp2_rtupdate, metric 23284736 succ 1 for 100-100, is: 100.1, n h: 100.1, idb: Serial2.1 02:44:47: AT: atigrp2_rtdelete, deleting 30-30 from 100.1 on Serial2.1 02:44:47: AT: atigrp2_rtupdate, metric 23310336 succ 0 for 30-30, is: 100.1, nh: 100.1, idb: Serial2.1 02:44:47: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1 02:44:47: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
router2(config)#end router2# 02:51:19: %SYS-5-CONFIG_I: Configured from console by console router2#sh apple ro Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP S - static P - proxy 3 routes in internet
The first zone listed for each entry is its default (primary) zone.
C Net 11-20 directly connected, Ethernet0, zone Router2Ethernet E Net 30-30 [1/G] via 100.3, 1171 sec, Serial2.1, zone Router3Ethernet C Net 100-100 directly connected, Serial2.1, zone FrameRelay router2#
router3# router3#sh apple ro Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP S - static P - proxy 3 routes in internet
The first zone listed for each entry is its default (primary) zone.
E Net 11-20 [1/G] via 100.1, 1185 sec, Serial2.1, zone Router2Ethernet C Net 30-30 directly connected, Ethernet0, zone Router3Ethernet C Net 100-100 directly connected, Serial2.1, zone FrameRelay router3#
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:22:53 GMT-3