From: Richardson, Cheryl (cheryl.richardson@xxxxxxxx)
Date: Mon Jul 12 1999 - 21:49:20 GMT-3
Ben,
It doesn't appear as if you are getting your prefixes. Typically you
would get this from the ATM switch (LS1010, 8540, etc).
The "show lane default" would look like the following:
ROUTER1>show lane default-atm-addresses
interface ATM5/0:
LANE Client: ...0050BD2E948C.**
LANE Server: ...0050BD2E948D.**
LANE Bus: ...0050BD2E948E.**
LANE Config Server: ...0050BD2E948F.00
note: ** is the subinterface number byte in hex
interface ATM6/0:
LANE Client: 47.009181000000001011BA9701.0050BD2E94A8.**
LANE Server: 47.009181000000001011BA9701.0050BD2E94A9.**
LANE Bus: 47.009181000000001011BA9701.0050BD2E94AA.**
LANE Config Server: 47.009181000000001011BA9701.0050BD2E94AB.00
note: ** is the subinterface number byte in hex
ATM5/0 is not communicating correctly to the switch, whereas ATM6/0 is. How
does your ATM switch connection look?
Cheryl Richardson
> -----Original Message-----
> From: Derek Fage [SMTP:DerekF@itexjsy.com]
> Sent: Monday, July 12, 1999 4:42 PM
> To: 'Ben Rife'; ccielab@groupstudy.com
> Subject: RE: ATM
>
> Ben,
>
> Bear in mind that I have no access to ATM, although I did configure this
> up
> on the BRS course at ARS, here's my take on this...
>
> 1. Get the NSAP address of the servers by using SHOW LANE DEFAULT and
> making
> a note of the LAND Server: entry (do this for all of the servers you want
> to
> configure). Ensure you include the selector byte
>
> 2. Create the LANE database in global config mode as follows:
>
> lane database ccie
> name elan1 server-atm-address 47.00mumblemumble.01
> name elan1 server-atm-address 47.00mumblemumble.01
>
> 3. Add the following lines to your ATM0 interface:
>
> lane database ccie
>
> Derek...
>
> > -----Original Message-----
> > From: Ben Rife [SMTP:brife@bignet.net]
> > Sent: 12 July 1999 21:24
> > To: ccielab@groupstudy.com
> > Subject: ATM
> >
> > Hi Guys,
> >
> > I'm on a CAT5 with a LANE card. I'm trying to configure LANE, right
> > now I'm trying to configure the LEC/LECS/BUS/LES. Here's my config thus
> > far:
> >
> > interface ATM0
> > atm pvc 1 0 5 qsaal
> > atm pvc 2 0 16 ilmi
> > lane auto-config-atm-address
> > !
> > interface ATM0.1 multipoint
> > lane server-bus ethernet elan1
> > lane client ethernet 1
> >
> > I don't know how/where to configure the ATM address for each service
> > though. When I enter "sh lane default" here's what I get:
> >
> > ATM#sh lane def
> > interface ATM0:
> > LANE Client: ...00602F7FCD40.**
> > LANE Server: ...00602F7FCD41.**
> > LANE Bus: ...00602F7FCD42.**
> > LANE Config Server: ...00602F7FCD43.00
> > note: ** is the subinterface number byte in hex
> >
> > Any ideas? Thanks.
> >
> > 1 day away...
> >
> > Benjy Rife
> > MCSE, CNE, CCIE Candidate
> > brife@bignet.net <mailto:brife@bignet.net>
> > www.bignet.net/~brife <http://www.bignet.net/~brife>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:21:42 GMT-3