From: "Rudy Phen" (rudy.phen@xxxxxxxxxxxxxxxxxx)
Date: Fri Jun 04 1999 - 22:39:01 GMT-3
Thanks for all the input..
but I already did all the suggestion you gave.. but the problem is still there.
.
finally I just realize I mistakenly type the incorrect ipx address of the other
spoke router when using frame-relay map ipx command. after change to the corre
ct ipx address, the configuration work.
Thank again..
btw I need info about the second day on ccie lab test. What kind of question fo
r the desktop and IBM networking also for the troubleshooting session. any idea
..!
Best Regards,
Rudy Phen
STARtrac Datacraft Asia Ltd.
---------- Original Text ----------
From: "Joe Soricelli" <jsoricelli@ccci.com>, on 6/4/99 4:50 AM:
Without checking my documentation (always scary!!!), I think that another
alternative command to enable inverse-arp on a multipoint sub-interface, you
can type frame-relay interface-dlci <dlci>
-joe
-----Original Message-----
From: Srikanth Nagarajan <nsrikanth@hotmail.com>
To: Joel.Ekis@Connect.Xerox.com <Joel.Ekis@Connect.Xerox.com>;
rudy.phen@datacraft-asia.com <rudy.phen@datacraft-asia.com>;
ccielab@groupstudy.com <ccielab@groupstudy.com>
Date: Thursday, June 03, 1999 2:24 PM
Subject: RE: IPX over frame relay
>Another alternative is to enable inverse arp on the frame relay interface
by
>which both ends could determine their protocol addresses
>
>Command is
>
>(config-if)#frame-relay inverse-arp
>
>Thanks
>Srikanth N
>
>>From: "Ekis, Joel" <Joel.Ekis@Connect.Xerox.com>
>>Reply-To: "Ekis, Joel" <Joel.Ekis@Connect.Xerox.com>
>>To: rudy.phen@datacraft-asia.com, ccielab@groupstudy.com
>>Subject: RE: IPX over frame relay
>>Date: Thu, 3 Jun 1999 07:59:38 -0400
>>
>>You will need 'frame-relay map ipx ... broadcast' statements on every
>>spoke.
>>Otherwise you will not have IPX connectivity between the spokes. Also,
>>make
>>sure you turn off the IPX RIP or you will be dumping extra broadcast
>>traffic
>>on the F/R circuits needlessly.
>>
>>Joel Ekis, CCNA, CCDA
>>Xerox Connect
>>Sr. Enterprise Consultant/Enterprise Network Services
>>Phone: 913-696-0888, x234
>>Pager: 800-697-0359
>>joel.ekis@connect.xerox.com <mailto:joel.ekis@connect.xerox.com>
>>
>>
>> -----Original Message-----
>> From: rudy.phen@datacraft-asia.com
>>[SMTP:rudy.phen@datacraft-asia.com]
>> Sent: Thursday, June 03, 1999 6:28 AM
>> To: ccielab@groupstudy.com
>> Subject: IPX over frame relay
>>
>> Next month is a big day... hopefully new CCIE coming...
>> I am currently testing on my lab for ipx over frame relay
>>configuration.
>> I did not using subinterfaces.. but i using IPX Eigrp on the hub dan
>>spoke router and I turn off the split horizon.
>> the result is I got all the ipx route.. (perfect..)
>> but the problem is I can not ping from one spoke router to another
>>spoke router.. even ping to the frame relay interface on that spoke router
>>(that connected to hub router)..
>> I have check all the config.. it's look correctly configure..
>> Pls consult..... thanks in adv..
>>
>> Cheers
>> Rudy Phen
>> Startrac - Datacraft Asia Ltd.
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:21:38 GMT-3